06-Other Construction Materials



ANNEXURE-VI

RATES OF OTHER CONSTRUCTION MATERIALS

No extra on cost, conveyance charges shall be allowed for all the items included Note: under this category. The rates approved therein are applicable at site of work

Sl. No. Name of Material Unit Basic Rate approved for the year 2020-2021
(w.e.f. 20.04.2020)
1 Water Proofing Compound Kg 41.90
2 Mild Steel Flats of all sizes Kg 40.45
3 Mild Steel Square Rods of all sizes Kg 40.45
4 First Quality Design Ceramic Tiles of all Colours    
i 305mm x 305mm x 6mm Each 45.00
ii 200mm x 200mm x 6mm Each 19.80
iii 200mm x 100mm x 6mm Each 10.70
5 First Quality Plain Ceramic Tiles of all colours    
i 305mm x 305mm x 6mm Each 32.20
ii 200mm x 200mm x 6mm Each 14.40
iii 200mm x 100mm x 6mm Each 7.40
6 Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm Each 53.00
7 Solar Reflective Ceramic Tiles of size    
a 305mm x 305mm x 7mm thick sqm. 464.00
b 305mm x 240mm x 6mm thick sqm. 383.00
8 Dadooing  Ceramic Tiles of size 300mm x 450mm x 8mm Each 57.20
9 Dadooing Ceramic Tiles of size 300mm x 600mm x 10mm Each 85.00
10 First Quality White Glazed Tiles    
i 150mm x 150mm x 6mm Each 7.70
ii 100mm x 200mm x 6mm Each 6.70
11 First Quality Colour Glazed Tiles    
i 150mm x 150mm x 6mm Each 8.90
ii 100mm x 200mm x 6mm Each 7.70
12 First Quality Colour Glazed Tiles with Printed Design    
i 150mm x 150mm x 6mm Each 10.50
       
ii 100mm x 200mm x 6mm Each 9.50
13 Colour Designed Glazed Tiles 300 x 200 x 6mm Each 28.30
14 Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm sqm. 603.00
15 Double Charged Vitrified Tiles 600 x 600 x 8mm sqm. 900.00
16 Double Charged Vitrified Tiles 800 x 800 x 10mm sqm. 1150.00
17 Pre-polished  Concrete  Anti-Skid  Step  Tiles  of  20mm thick sqm. 599.00
18 Rubber Moulded Hydraulic Pressed Paver Block    
a 83mm thick sqm. 542.00
b 63mm thick sqm. 451.00
19 TAMIN Paver Block of size – Supply at site    
a 60mm thick sft. 50.60
b 80mm thick sft. 60.60
20 Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person sqm. 2000.00
21 Providing  and  filling  the  tile  joint  with  epoxy  grout  with following specification:
Surface  preparation  including  cleaning  the  joint  to  be  free from  dust  and  loose  particles.   Providing  masking  tape  on either side of the tile joint  edges and providing  sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers.  The rate inclusive of cost of materials and labour, etc., complete.
sqm. 430.00
  New Item    
22 SRC Cement (Sulphate Resistant Cement) 50 Kgs. / Bag 300.00
23 Slag Cement 50 Kgs. / Bag 270.00
24 White Cement Kg 22.20
25 Colour  Cement  (White  Cement  mixed  with  Colouring Pigments) Kg 26.80
26 Multi-Colour Marble Chips of all grades / sizes Bag 89.40
27 White Marble Slab (Adanga) 18mm to 20mm Thick    
i 4'0'' x 2'0'' and above sqm. 1378.00
ii 2'0'' x 2'0" or 2'0" x 1'0" or 1'0" x1'0" sqm. 688.00
28 Granite  Tiles  -  (Superfine  Polished  with  Machine  Cut Edges) of size 2'0" x 1'0" or 1'0" x 1'0" or 1'0" x 0'6" of
10 mm thick
   
a Jet Black sqm. 844.00
b Ruby Red, Raw Silk sqm. 756.00
c Sinthetic Grey, Paradise and similar varieties sqm. 714.00
29 Granite  Slabs  (Super  Fine  Polished  with  Machine  Cut Edges) of sizes  4'x2' and above 18mm to 20mm thick    
a Jet Black sqm. 1706.00
b Ruby Red, Raw Silk sqm. 1595.00
c Sinthetic Grey, Paradise and similar varieties sqm. 1434.00
d Fine Polished Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 1484.00
e Fine Polished Blue Pearl Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 7423.00
30 Flamed Steel Grey Granite Slab
1200mm x 600mm, 16mm to 18mm Thick
sqm. 1797.00
31 Flamed Ruby Red Granite Slab
1200mm x 600mm, 16mm to 18mm Thick
sqm. 1908.00
32 Nosing for Granite Slab    
a Single  Nosing RM 191.90
b Double Nosing RM 363.00
33 Polished   Shahabad   Stone   Slabs   20mm   thick   with Machine Cut Edges of size below 2'0" x 2'0" sqm. 312.00
34 Polished  Shahabad  Stone  Slabs  of  20mm  thick  with Machine Cut Edges of size 2'0" x 2'0" and above sqm. 370.00
35 Polished  Rajasthan  Kota  Stone  Slabs  of  20mm  thick with Machine Cut Edges of size below 2'0" x 2'0" sqm. 476.00
36 Polished  Rajasthan  Kota  Stone  Slabs  of  20mm  thick with Machine Cut Edges of size 2'0" x 2'0" and above sqm. 540.00
37 Dolphur Stone Slabs - Semi Polished with Machine Cut Edges of all sizes    
a 40mm thick sqm. 412.00
b 20mm thick sqm. 375.00
38 PVC Trims (Beading) RM 90.00
39 Terracota Jally of size 20 x 20 x 0.75mm Each 38.30
40 Aluminium Strips of size 40mm wide x 1.5mm thick RM 32.30
41 Brass Strips of size 40mm wide x 1.5mm thick RM 67.90
42 Glass Strips of size 40mm wide and 4mm thick RM 15.40
43 Marblex Tiles 3mm thick sqm. 664.00
44 Red Oxide - Superior quality for floor finish Kg 142.40
45 Decorative Pressed Tiles of 12mm thick of all sizes and shapes sqm. 1055.00
46 Exterior Emulsion Paint - Water Based Primer (Liquid) Litre 148.40
47 Alkali Resistant Distemper Primer Litre 133.00
48 Sandtex Matt Litre 155.00
49 Vinaratex or Equivalent Textured Coat sqm. 199.90
50 Best Lac Polish / French Polish Litre 259.00
51 Varnish Litre 266.00
52 Cotton Waste Kg 10.20
53 Cement  Based  Hydraulically  Pressed  Anti  skid  Tiles (Pattern Design) - 20mm thick sqm. 500.00
54 Marble Powder Kg 4.49
55 Polishing Stone    
i Rough Each 65.80
ii Medium Each 87.90
iii Fine / Nice Each 100.70
56 Oxalic Acid Kg 38.10
57 Tupentine Litre 23.30
58 Mansion polish 400 gram 146.30
59 Poly Sulphide Kg 173.60
60 Primer for Expansion Joints Kg 149.30
61 Filler Material sqm. 142.40
62 Bond Breaker RM 3.68
63 PVC Water Bar 150mm wide with Singlel Bulb RM 282.80
64 Plain GI Sheet 0.8mm thick (22 Gauge) sqm. 357.50
65 Phil Plug Each 4.95
66 GI Screws    
i 30mm x 6mm Each 1.26
ii 19mm x 6mm Each 0.80
67 GI Limpet / Cup Washers Each 1.86
68 Bitumen Washers 15mm dia Each 1.11
69 Asbestos Cement Pipe - 100mm dia 3 RM 141.30
70 AC Shoe - 100mm dia Each 44.80
71 AC Bend - 100mm dia Each 51.30
72 AC Cylindrical Cowl - 100mm dia Each 77.00
73 CI Brackets for AC Pipe 100mm dia Each 19.70
74 CI Grating - 100mm dia Each 31.50
75 Asbestos Cement Fully Corrugated Sheet - 6mm thick sqm. 186.00
76 Asbestos cement plain sheet    
i 6mm thick sqm. 166.90
ii 4mm thick sqm. 115.60
  New Item    
77 Supplying  and  fixing  Shade  Net  (Green  Net)  for under construction of high rise building sqm. 66.00
78 Asbestos Cement Adjustable Ridges Pair 192.60
79 GI "J" or "L" Bolts with Nuts 6mm dia Each 3.84
80 Steel  -  Special  Extruded  Sections  for  Steel  Windows and   Ventilators   conforming   to   ISS   7452   /   1990 including fabrication charges Kg 61.50
81 CRCA Pressed Steel Box Section 18 Gauge or  1.25mm thick  for  Door  Frames  including  providing  holes  and fixing wooden blocks for fixing furniture and fittings    
a With one coat of Red Oxide priming coat RM 353.00
b With Powder Coated Primer RM 376.70
82 Aluminium  Extruded  Sections  (for  Doors,  Windows, Ventilartors,  Partitions,  False  Ceiling  etc)  including charges for anodising for 15 micron thickness    
a Natural Colour Matt Finish Kg 287.00
b With Powder Coating of any colours Kg 307.00
83 Alumninum  Extruded  Box  Section  for  Staircase  Hand Rails  including  charges  for  anodising  for  15  micron thickness - Natural colour matt finish Kg 359.00
84 Rubber Beading for Aluminium Glazed Doors RM 37.60
85 Rubber Beading for Aluminium Glazed windows RM 28.60
86 PVC / Woollen Felt for Aluminium Doors 6mm thick RM 7.55
87 Pivot for Aluminium Door Set 147.40
88 Hydraulic  Door  Closer  of  various  sizes  of  approved quality   using   Aluminium   Extruded   Section   Body Tubular  Type  Universal  Hydraulic  Door  Closer  with Double   Speed   Adjustment   like   HARDWYN   (make) 'GAZEL' (or) Equivalent (with ISI Monogram) Each 890.00
89 Hydraulic Floor Springs of various sizes, Double Acton Hydraulic  Floor  Spring  of  approved  quality,  brand, manufacture  asper  BIS  Standards  for  doors  including cost  of  cutting  floors  as  required,  embedding  in  to floors and stainless steel cover plates with aluminium pivot  and  single  piece  MS  sheet  outer  box  with  side plate etc., capaple of taking upto 130 kg. weight from door   shutter,   like   HARDWYN   make   (U-32)   or   its Euivalent with ISI monogram. Each 2055.00
90 Lock for Aluminium Doors Each 251.00
91 Lock for Aluminium Sliding Windows Each 62.80
92 Aluminium Grill of Standard Pattern (Diamond Shape) - 10mm thick including 'F' (or) 'H' Section sqm. 1835.00
93 Aluminium Grill of Standard Pattern (Diamond Shape) - 6mm thick including 'F' (or) 'H' Section sqm. 1485.00
94 Bolts and Nuts 10mm dia for False Ceiling Each 5.55
95 Rawl Plugs for False Ceiling Each 9.40
96 PVC Roller for Sliding Windows Each 13.85
97 Synthetic Resin - Fevicol or Equivalent (Phenol Formal Dehide Based Resin) Kg 195.90
98 Butt  Hinges  with  Nylon  Washers  of  various  sizes  of Length and Width (with required screws)    
a 125mm x 30mm Each 79.10
b 100mm x 30mm Each 63.50
c 75mm x 30mm Each 43.60
d 50mm x 30mm Each 35.15
  New Items    
99 Brass Hinges    
a 125mm x 30mm Each 210.00
b 100mm x 30mm Each 180.00
c 75mm x 30mm Each 150.00
d 50mm x 30mm Each 125.00
100 Tower  Bolts  of  various  lengths  and  diametre  (with required screws)    
a 400mm long and 12mm dia Each 149.70
b 300mm long and 12mm dia Each 115.20
c 250mm long and 12mm dia Each 86.30
d 200mm long and 12mm dia Each 72.60
e 150mm long and 12mm dia Each 57.20
f 100mm long and 10mm dia Each 50.30
g 75mm long and 10mm dia Each 35.10
  New Items    
101 Brass Tower Bolts    
a 400mm x 12mm Each 1000.00
b 300mm x 12mm Each 750.00
c 200mm x 12mm Each 530.00
d 150mm x 12mm Each 400.00
e 100mm x 10mm Each 320.00
f 75mm x 10mm Each 200.00
102 Aldrops of following lengths and diametre with required screws, bolts and nuts    
a 300mm long and 16mm dia Each 185.20
b 250mm long and 16mm dia Each 159.70
c 200mm long and 16mm dia Each 108.10
d 200mm long and 12mm dia Each 89.70
  New Items    
103 Brass Aldrops    
a 300mm x 16mm Each 950.00
b 250mm x 16mm Each 820.00
c 200mm x 16mm Each 700.00
d 200mm x 12mm Each 500.00
104 Handles "D" type of various sizes with required screws    
a 200mm long Each 56.70
b 150mm long Each 50.90
c 100mm long Each 31.20
105 Ornamental  Handles  of  various  sizes  with  required screws    
a 200mm long Each 146.30
b 150mm long Each 97.50
c 100mm long Each 53.80
  New Items    
106 Brass Ornamental Handles    
a 200mm Each 390.00
b 150mm Each 250.00
c 100mm Each 180.00
107 Aluminium   Door   Stopper   with   Rubber   Bush   with required screws Each 43.80
108 Rubber Bush - 40mm dia and 60mm long with required screws Each 22.70
109 Mortice  Lock  (Godrej   or  Equivalent)   with   required screws with 3 Keys    
a With Night latch Each 530.00
b Without Night latch Each 394.00
c Wire Nails Kg 62.80
110 Teakwood Beading    
a 15mm x 12mm RM 15.15
b 35mm x 12mm RM 38.40
111 Teakwood Beading (Ordinary)    
a 30mm x 12mm RM 31.90
b 25mm x 12mm RM 25.60
112 Teakwood Beading - Ornamental / Design    
a 40mm x 12mm RM 89.70
b 40mm x 15mm RM 102.80
c 25mm x 12mm RM 70.30
d 15mm x 12mm RM 48.30
113 Medium  Desity  Fibre  (MDF)  Board  -  Exterior  Grade, both sides pre-lamiated including external lipping with kiln dried soft wood 35mm thick sqm. 2141.00
114 Medium Density Fibre (MDF) Board - Exterior Grade - both sides pre-laminated, 12mm thick sqm. 1030.00
115 MDF  Board  Exterior  Grade  -  Plain  including  external lipping with kiln dried soft wood    
i 35mm thick sqm. 1747.00
ii 30mm thick sqm. 1610.00
116 Medium   Density   Fibre   (MDF)   Board   12mm   thick Exterior Grade with Melamine finish    
a One Side Melamine Finish sqm. 1090.00
b Both Sides Melamine Finish sqm. 1227.00
117 Medium Density Fibre (MDF) Board - Exterior Grade - Plain with teakwook external lipping alround    
a 35mm thick sqm. 1878.00
b 30mm thick sqm. 1666.00
118 Solid  Core  Flush  Shutters  with  teakply  on  both  side with teakwook lipping alround 35mm thick sqm. 2211.00
119 Solid Core Flush Shutters with teakply on one side and commercial  ply  on  other  side  with  teak  wook  lipping alround 35mm thick sqm. 1944.00
120 Solid Core Flush shutters with commercial ply on both side with teakwook lipping alround  35mm thick sqm. 1666.00
121 Providing  Cup-board  Shutter  using  termite  /  water  proof plywood  of  19mm  thick  over  which  laminated  sheet  of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture   fittings,   such   as,   hydralic   hinges,   tower   bolt, handles,   multi   purpose   locks   etc.,   as   directed   by   the Departmental   Officers.   The   design   pattern,   water   proof plywood,  laminate  sheet  and  other  materials should  be got approved from the Executive Engineer befoe use on work. sqm. 4949.00
122 Solid  PVC  Door  Shutters  using  19  Gauge  19mm  MS square tubes  for  styles and  outer frames.   15mm  MS square tubes for top, lock and bottom rails.  The steel tubes  shall  be  covered  with  5mm  thick  solid  PVC Sheets.  Shutter using 5mm thick solid PVC Sheets for panelling   shall   rigidly   fixed   in   position   including necessary  furniture  and  fittings.   The over all  size of styles shall be 50mm x 30mm.  The over all size of top rail,  lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter    
a Solid panel PVC door with frame sqm. 2828.00
b Solid Panel PVC Door without Frame sqm. 2383.00
123 Supplying and fixing of PVC Sliding Door with Roller sqm. 3030.00
124 a FRP  Door  Sutter  with  FRP  Door  Frames  made  out  of FRP  Sheets  of  3mm  thick  of  over  all  size  65mm  x 50mm with rebate suitably reinforced using MS Angle / Flats,  cost  of  holdfasts  and  Solid  Core  FRP  Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers sqm. 3918.00
b Excluding door frames sqm. 3009.00
125 a PVC  Panelled  door  Shutters  Hollow  Type  -  200mm  x 20mm panels with 1mm wall thickness for panels and styles   and   rails   of   suitable   size   with   2mm   wall thickness  suitably  reinforced  using  MS  Angle  /  Flat including cost of necessary aluminium hinges and other furniture fittings sqm. 2014.00
b Excluding Door Frames sqm. 1701.00
126 RCC  Door  Frame  of  100mm  x  65mm  cross  sectional size  with  necessary  rebate  for  housing  the  shutters, manufactured with  cement concrete of grade not less than  M20  using  10mm  and  below  graded  stone  jelly and  using  steel  reinforcement  as  per  CE  (B)  Circular instructions RM 275.00
127 Stainless  Steel  (Salem  Stainless  Steel)  Door  Frame (Box Section using Stainless Steel Plate of 1mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm  on  one  side  of  the  frame  including  supplying and fixing dovetail splayed end stainless steel Hold fast etc RM 900.00
128 Stainless  Steel  (Salem  Stainless  Steel)  Door  Frame (Box  Section  using  Stainless  Steel  Plate  of  1.6mm thick)  of  size  100mm  x  60mm  with  a  rebate  of  30  / 35mm  x  15mm  on  one  side  of  the  frame  including supplying  and  fixing  dovetail  splayed  end  stainless steel hold fast etc RM 1217.00
129 Supplying  and  Erecting  Pull  and  Push  Type  Rolling Shutter  with  ISI  make  of  approved  size  and  section using 18 GI sheet.  The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc    
A ROLLING SHUTTERS (WITH ISI MONOGRAM)    
a Manually Operated (up to 8 sqm. Area) sqm. 2131.00
b Gear Operated Type (from 8 sqm. to 12 sqm. Area) sqm. 2373.00
c Electrically Operated Type (exceeding 12 sqm. Area) sqm. 2575.00
B ROLLING GRILLS (WITH ISI MONOGRAM)    
a Manually Operated (up to 8 sqm. Area) sqm. 2171.00
b Gear Operated Type (from 8 sqm. to 12 sqm. Area) sqm. 2444.00
c Electrically Operated Type (exceeding 12 sqm. Area) sqm. 2716.00
130 Barbed Wire - 10 Gauge - Two Ply and Four Pronged (Galvanised) 1 Kg or
6 RM
60.90
131 Chain Link - 2" x 2" using 10 Gauge Galvanised Iron Wire (of all sizes) sqm. 157.20
132 Pin Headed / Fluted / Figured Glass 3mm thick sqm. 222.20
133 Plain Glass - 4mm thick sqm. 300.90
134 Plain Sheet  Glass - 5.5mm thick sqm. 355.50
135 Metal Screws (for Aluminium Doors, Windows etc)    
i 75mm x 8mm Each 2.17
ii 38mm x 6mm Each 1.52
iii 19mm x 8mm Each 1.06
iv 19mm x 6mm Each 0.80
136 Cement Paint (First Quality) Kg 48.95
137 Oil Bound Distemper Kg 72.40
138 Acrylic Distermper Kg 83.60
139 Primer for Plastic Emulsion Paint Litre 144.70
140 Plastic Emulsion Paint (First Quality) Litre 289.80
141 Wood Primer Litre 144.70
142 Synthetic Enamel Paint for Wood Work Litre 234.30
143 Red Oxide Primer for Iron Work Litre 134.30
144 Synthetic Enamel Paint for Iron Work Litre 223.20
145 Melamine Polish Sqm. 636.00
146 Exterior Emulsion Paint Litre 297.90
147 Painting  the  wall  with  Texture  Finish  Paint  including labour charges sqm. 404.00
148 White Wall Putty Powder Kg. 27.00
148 a Sand Paper (Water Proof Abrasive Sheet) Each 10.00
148 b 8" Putty Blade Dozen 120.00
148 c 6" Putty Blade Dozen 90.00
149 300mm dia RCC Hume Pipe RM 2206.00
150 GI Pipes "B" Class    
i 65mm dia RM 244.40
ii 50mm dia RM 209.00
iii 40mm dia RM 163.00
iv 32mm dia RM 151.40
v 25mm dia RM 128.00
vi 20mm dia RM 98.60
vii 15mm dia RM 69.80
151 GI Specials    
A Union    
i 50mm dia Each 266.30
ii 40mm dia Each 197.50
iii 32mm dia Each 127.50
iv 25mm dia Each 98.60
v 20mm dia Each 69.80
vi 15mm dia Each 58.10
B GI Elbow    
i 50mm dia Each 128.00
ii 40mm dia Each 98.60
iii 32mm dia Each 87.00
iv 25mm dia Each 58.10
v 20mm dia Each 25.40
vi 15mm dia Each 15.90
C GI Bend    
i 50mm dia Each 116.30
ii 40mm dia Each 87.00
iii 32mm dia Each 69.80
iv 25mm dia Each 52.00
v 20mm dia Each 23.20
vi 15mm dia Each 13.60
D GI TEE    
i 50mm dia Each 139.80
ii 40mm dia Each 110.20
iii 32mm dia Each 98.60
iv 25mm dia Each 81.40
v 20mm dia Each 34.70
vi 15mm dia Each 28.60
E GI COUPLING    
i 50mm dia Each 69.80
ii 40mm dia Each 58.10
iii 32mm dia Each 46.50
iv 25mm dia Each 28.60
v 20mm dia Each 15.90
vi 15mm dia Each 13.60
F GI REDUCER    
i 50mm x 40mm dia Each 93.20
ii 40mm x 32mm dia Each 69.80
iii 32mm x 25mm dia Each 52.00
iv 25mm x 20mm dia Each 28.60
v 20mm x 15mm dia Each 20.30
vi 40mm x 25mm dia Each 52.00
vii 32mm x 20mm dia Each 40.40
G GI REDUCER ELBOW    
i 50mm x 40mm dia Each 110.20
ii 40mm x 32mm dia Each 93.20
iii 32mm x 25mm dia Each 69.80
iv 25mm x 20mm dia Each 52.00
v 20mm x 15mm dia Each 40.40
vi 40mm x 25mm dia Each 72.70
vii 32mm x 20mm dia Each 57.60
H GI REDUCER TEE    
i 50mm x 40mm dia Each 139.80
ii 40mm x 32mm dia Each 116.30
iii 32mm x 25mm dia Each 98.60
iv 25mm x 20mm dia Each 75.30
v 20mm x 15mm dia Each 69.80
vi 40mm x 25mm dia Each 104.70
vii 32mm x 20mm dia Each 81.40
I GI HEX NIPPLE    
i 50mm dia Each 87.00
ii 40mm dia Each 69.80
iii 32mm dia Each 58.10
iv 25mm dia Each 43.70
v 20mm dia Each 34.70
vi 15mm dia Each 23.20
152 Gun Metal Gate Valve (Heavy Duty)    
i 65mm dia Each 1494.00
ii 50mm dia Each 1217.00
iii 40mm dia Each 959.00
iv 32mm dia Each 746.00
v 25mm dia Each 582.00
vi 20mm dia Each 344.00
  Note: Gate Valves should be used only in delivery line to OHT Scour Pipe in OHT (for cleaning of OHT) where pressure pumping is involved.  In all other cases only wheel valve should be used    
153 Gun Metal Wheel Valve (Heavy Duty)    
i 40mm dia Each 640.00
ii 32mm dia Each 503.00
iii 25mm dia Each 345.00
iv 20mm dia Each 237.00
v 15mm dia Each 167.00
154 Brass  Chromium  Plated  Screw  Down  Tap  15  /  12mm dia (Heavy Type) Each 202.00
155 Brass Chromium Plated Pillar Tap (Heavy Type) - 15 / 12mm dia Each 265.00
156 PVC Screw Down Tap Heavy Type 20mm dia Each 80.00
157 PVC Screw Down Tap Heavy Type 15mm dia Each 62.00
158 Chromium Plated Stop Cock 15mm dia Each 148.40
159 Brass Chromium Plated Shower Rose - 100mm dia Each 190.80
160 CP Wall Mixture Tap 3 in 1 system with Hand Showers Each 4065.00
161 CP Two Way Bib Cock with Health Faucet Each 2020.00
162 CP Shower Arm with Overhead Shower Rose Each 1160.00
163 Wooden Plug, Clamp and Screws Set 12.00
164 Shellac 100 gram 18.15
165 PVC Adhesive (Solution) 100 gram 34.00
  New Items    
166 UPVC Adhesive 100 Gram 80.00
167 CPVC Adhesive 100 Gram 110.00
168 Vajjram Kg. 77.00
169 Thread Ball Each 3.53
170 CP Heavy Duty Bottle Trap 32mm Each 1085.00
171 CP Angle Cock Tap Each 762.00
172 Oriya Type Indian Water Closet 580mm x 440mm with "P" or "S" Trap    
i White Set 1180.00
ii Colour Set 1504.00
173 European  Water  Closet  with  "P"  or  "S"  Trap  with Double Flapped Seat and Seat Cover with Brass Hinges and 10 litre capacity PVC Low Level Flusing Tank with all internal fittings    
i White Set 3030.00
ii Colour Set 3420.00
174 European  Water  Closet  with  "P"  or  "S"  Trap  with Double Flapped Seat and Seat Cover with Brass Hinges and  12.5  litre  capacity  Porcelain  Low  Level  Flusing Tank with all internal fittings    
i White Set 4270.00
ii Colour Set 5140.00
175 PVC   low   level   flushing   tank   with   all  internal fittings (wall mounting type)    
a White - 10 litre capacity Set 847.00
b White - 7.5 litre capacity Set 647.00
c Colour - 10 litre capacity Set 959.00
d Colour - 7.5 litre capacity Set 762.00
176 PVC Water Tank Litre 8.60
177 SS Elbow Action Tap of size 15mm Each 1515.00
178 SS Heavy Duty Long Body Tap 15mm Each 1515.00
179 SS Swan Neck Tap Each 1010.00
180 Wash  Hand  Basin  of  size  550mm  x  400mm  with  all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class  GI  Waste  Pipe,  15mm  dia  GM  Wheel  Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc    
i White without Pedastal Set 1640.00
ii White with Pedastal Set 1974.00
iii Colour without Pedastal Set 2196.00
iv Colour with Pedastal Set 2429.00
181 White  Porcelain  Sink  of  size  600mm  x  450mm  x 200mm with 32mm dia 'B' Class GI Waste Water Pipe and 32mm dia CP Waste Coupling Set 2105.00
182 Cuddapah  Slab  Sink  of  size  600mm  x  450mm  x 200mm with 32mm dia 'B' Class GI Waste Water Pipe & 32mm dia CP Waste Coupling Set 755.00
183 Cuddapah  Slab  Sink  of  size  600mm  x  600mm  x 200mm with 32mm dia 'B' Class G.I. waste water pipe & 32mm dia C.P. waste coupling. Set 1000.00
  New Items    
184 Stainless Steel Sink    
a 600mm x 600mm x 200mm Each 9000.00
b 600mm x 450mm x 200mm Each 7000.00
185 Lipped   Mouth   Porcelain   Flat   Back   Urinal   with   all accessories   such   as   32mm   dia   Bell   Mouth   PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class   GI   Waste   Water   Pipe,   15mm   dia   Nylon Connection, 15mm dia Brass Nipple etc.    
i White Set 922.00
ii Colour Set 1055.00
186 Supplying and fixing of SS Sink of size 1200 x 550 x 180mm Each 18180.00
187 Supplying and fixing of Granite Sink of size 600 x 600 x 250mm Each 4066.00
188 Supplying and fixing of Ornamental Type White Glazed Porcelain  Corner  'L'  Type  Wash  Hand  Basin  of  size 350mm Each 3484.00
189 Supplying and fixing of Oval Shape Wash Hand Basin of size 560 x 450mm Each 2843.00
190 Supplying  and  fixing  of  White  Glazed  Porcelain  Oval Shape Special Type Urinal of size 382 x 398 x 601mm Each 9872.00
191 Porcelain Soap Dish of size  150mm x 150mm x 50mm    
i White Each 192.40
ii Colour Each 263.60
192 Brass  Chromium  Plated  Soap  Tray  of  size  150mm  x 100mm Each 161.90
193 Brass  Chromium  Plated  Towel  Rail  60cm  long  and 20mm dia with Brackets Set 263.80
194 SS Towel Rack 600mm long with Lower Hanger Each 1515.00
195 Anodised  Aluminium Towel Rail 60cm long and 20mm dia with Brackets Set 128.00
196 PVC  /  Fibre  Glass  Framed  5.5mm  thick  Mirror,  Shelf Type with Hard Board Backing    
i 600mm x 450mm Each 466.60
ii 500mm x 400mm Each 375.70
197 Special Type Mirror of size 1000 x 780mm Each 2525.00
198 Stoneware Gully Trap of size 150mm x 100m with Cast Iron Double Gratings Each 167.10
199 Cast  Iron  Nahini  /  Floor  Trap  with  Stainless  Steel Grating    
i 100mm x 75mm Each 274.20
ii 75mm x 50mm Each 214.80
200 PVC Nahini / Floor Trap with PVC Grating    
i 100mm x 75mm Each 151.50
ii 75mm x 50mm Each 132.70
201 First Quality Cast Iron Pipe    
i 150mm Dia RM 994.00
ii 100mm Dia RM 599.00
iii 75mm Dia RM 478.00
iv 50mm Dia RM 339.00
202 First Quality Cast Iron Specials    
A Plain Bend    
i 150mm dia Each 538.00
ii 100mm dia Each 262.00
iii 75mm dia Each 202.00
iv 50mm dia Each 154.00
B Bend with Door    
i 150mm dia Each 623.00
ii 100mm dia Each 315.00
iii 75mm dia Each 262.00
iv 50mm dia Each 208.00
C Plain TEE    
i 150mm dia Each 1078.00
ii 100mm dia Each 478.00
iii 75mm dia Each 327.00
iv 50mm dia Each 225.00
D TEE with Door    
i 150mm dia Each 1139.00
ii 100mm dia Each 551.00
iii 75mm dia Each 382.00
iv 50mm dia Each 273.00
E "Y" Junction with Door (Single)    
i 150mm dia Each 1197.00
ii 100mm dia Each 599.00
iii 75mm dia Each 418.00
iv 50mm dia Each 298.00
F "Y" Junction with Door (Double)    
i 150mm dia Each 1320.00
ii 100mm dia Each 670.00
iii 75mm dia Each 502.00
G COWL    
i 150mm dia Each 327.00
ii 100mm dia Each 196.00
iii 75mm dia Each 131.00
iv 50mm dia Each 101.00
203 Stoneware Pipe    
i 150mm dia Each (0.6.RM) 100.00
ii 100mm dia Each (0.6.RM) 62.20
204 Stoneware Specials    
A Stoneware TEE    
i 150mm dia Each 162.90
ii 100mm dia Each 125.60
B Stoneware Bend    
i 150mm dia Each 138.00
ii 100mm dia Each 99.60
C Stoneware "Y" Junction    
i 150mm dia Each 168.00
ii 100mm dia Each 125.10
205 Spun Yarn Kg 12.90
206 Hemp Yarn Kg 11.60
207 Gunny Tape / Kithan sqm. 11.60
208 Tar Kg 40.30
209 Bitumen Felt 15mm thick Pad sqm. 230.00
210 Supplying,  fabricating,  erecting  and  fixing  Hilux  (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level    
a Using Hilux Board Plain Sheets (10mm thick) sqm. 954.00
b Using Perforated Sheets (10mm thick) sqm. 976.00
211 Supplying   and   laying   Glass   Wool   for   insulation including necessary packing materials    
a Using 50mm thick Glass Wool sqm. 385.00
b Using 25mm thick Glass Wool sqm. 205.00
  New Items    
212 Supply   and   installation   of   Anutone   (or)   Euivalent   Brand   of Acoustical False Ceiling of subtex nubby, square edge, glass fibre core  fully  encapsulated  ceiling  tile  of  size  595  x  595  x  15mm having volume density 120 Kgs / m3, weight 1.8 / 2.4 / 3 kg / m2  which  is  suspended  by  using  0.3mm  thick  skelet  trelis  T15 metal grid system.   Skelet trelis T15 metal grid system of 600 x 600mm   module   includes   skelet   WA15   W30   wall   angle  with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter  of  walls  with  the  help  of  nylon  sleeves  and  suitable fasteners  at  300mm  centers.   Then  suspend  the  skelet   MT15 W36  MainT  with  flange  width  15mm,  height  32mm  and  length 3600mm,  from  the  soffit  slab  with  help  of  soffit  cleat  and  wire rod  with  leveling  spring  clip  at  1200mm  centres.   Skelet  CT15 W12  CrossT  with  flange  width  15mm,  height  26mm  and  length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm  centers  in  the  perpendicular  direction  to  the  Main  T15. Finally,  the  skelet  CT15W06  CrossT  with  flange  width  15mm, height 26mm and length 600mm are interlocked into the precut slots in the CT15W12 CrossT in direction parallel to the Main T15 to result in 600 x 600mm module.  The subtex nubby square edge of size 595 x 595 x 15mm shall be placed into the grid size of 600 x  600mm.   Ensure  arrow  marks  behind  the  tiles  are  oriented  in one direction to achieve uniform shade.  The systems to achieve noise reduction coefficient not less than 0.9 NRC, so as to have an  neat  appearance  as directed  by  the  department  offices.   The cost   includes,   cost   of   material,   cost   of   labour,   scaffolding, transportation,     conveyance,     etc.     complying     to     standard specication. sqm. 1700.00
213 Supply  and  installation  of  Anutone  (or)  Equivalent  Brand  of Acoustical  False  Ceiling  of  Sisoli  Serene  /  Slate  Spirts  /  Slate Polka Mineral Fibre/ GRG Core Ceiling Tiles of size  595 x 595 x 15mm  having  volume  density  270  kgs  /  m3,  weight  4kg  /  m2 which is suspended by using 0.3mm thick skelet trelis T15 metal grid  system.   The  skelet  trelis  T15  metal  grid  system  of  600  x 600mm   module   includes   skelet   WA15   W30   wall   angle  with unequal flanges of 15 / 19mm, length 3000mm, fixed along the perimeter  of  walls  with  the  help  of  nylon  sleeves  and  suitable fasteners at 300mm centers.  Then suspend the skelet MT15 W36 MainT   with   flange   width   15mm,   height   32mm   and   length 3600mm,  from  the  soffit  slab  with  help  of  soffit  cleat  and  wire rod  with  leveling  spring  clip  at  1200mm  centres.   Skelet  CT15 W12  CrossT  with  flange  width  15mm,  height  26mm  and  length 1200mm is interlocked into the pre-cut slots in the Main T15 at 600mm  centers  in  the  perpendicular  direction  to  the  Main  T15. Finally skelet CT15 W06 CrossT with flange width 15mm, height 26mm and length 600mm are interlocked into the precut slots in the  CT15  W12  CrossT  in  direction  parallel  to  the  Main  T15  to result  in  600  x  600mm  module.   Sisoli  Serene  /  Slate  Spirts  / Slate  Polka  of  size  595  x  595  x  15mm  shall  be  placed  into  the grid  size  of   600  x  600mm.     The  systems  to  achieve  noise reduction coefficient not less than 0.5 NRC, so as to have an neat appearance  as  directed  by  the  department  offices.   The  cost includes,    cost    of    material,    cost    of    labour,    Scaffolding, transportation,    conveyance,    etc.,    complying    to    standard specication. sqm. 950.00
214 Supply  of  laying  of  Anutone  (or)  Equivalent  Brand  of Acoustical Insulation of Sound Synth Polywool, 50mm thick   made    from   recycled    poly    fibre    and   fully recyclable, surface density 1000 g / m2, weight 1.0 kg
/  m2  in  form  of  rolls  of  600mm  wide  and  15m  in length,  adhered  to  surface  with  stick  S7  adhesive  or held in position with chicken wire mesh etc., complying to standard specication.
sqm. 420.00
215 Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet  with following  specification and  the surface shall  be  cleaned  to  remove  all  dust,  foregin,  matters  lose materials or any other deposits of contamination by  rubbing with wire brush.
Slurry:  Dry  blend  and  polymer  liquid  blend  shall  be  mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix.   Any lumps found in mix shall be removed.
Apply  first  coat  of  polymer  modified  cementitious  slurry  by brush on wet cleaned surface.  After drying, second coat shall be applied on the first coat as directed by the departmental officers  etc.   The  rate  inclusive  of  cost  of  materials  and labour, etc., complete.
sqm. 323.00
216 Providing Cornice Work for Gyp Board False Ceiling RM 186.80
217 8mm   thick   Calcium   Silicate   Board   Designed   and Perforated for False Ceiling sqm. 1515.00
218 Termite Proof/Water Proof Plywood 19mm thick sqm. 1313.00
219 Laminated Sheet 0.8mm thick (inside) sqm. 242.00
220 Laminated Sheet 1mm thick (outside) sqm. 404.00
221 Squatting Urinal Set 446.00
222 CI Brackets for fixing the Sink Set 105.90
223 Swan Neck Tap Each 248.00
224 Brass Screws (30 x 6mm) Each 2.37
225 Brass Screws (75 x 10mm) Each 4.80
226 Special Clamp, Teakwood Plugs and Screws Set 21.20
227 PVC Clamp, Teakwood Plugs and Screws Set 8.35
228 Teakwood Plug Each 1.06
229 Teakwood Plug (50 x 50 x 100mm) Each 5.30
230 Manhole Cover 60 x 60cm (Heavy Duty) with Frame Each 1828.00
231 Welding Charges    
a 50mm Each 2.07
b 40mm Each 1.61
232 Add for Painting / Tarring for Hex Nipple Each 2.77
233 Labour Charges for fixing Cuddapah Slab to Cup-Board sqm 45.10
234 Hire Charges for Polishing Machinery Day 224.20
235 Electricity Charges Unit 11.70
236 Supplying and fixing in position White / Colour Glazed Model Floor  Mounted  European  Water  Closet  of  best  quality  and approved make with 100mm “P” or “S” trap connecting with CI  pipe  of  100mm  dia  /  PVC  pipe  of  110mm  dia,  double flapped  rigid  PVC  black  seat  and  seat  cover  with  CP  brass hinges  including  cost  of  white  cement,  cement  for  packing, spun  yarn,  teak  wood  plugs,  brass  screws,  etc.,  including supplying  and  fixing  10  litres  capacity  PVC  /  12.5  litres capacity  porcelin  low  level  flushing  tank  with  a  pair  of  CI brackets,  etc.,  complete  with  all  fittings,  such  as,  15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass  nipple  (2  Nos.),  15mm  nylon  connection,  TW  plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and  re-doing  the  dismantled  masonry  to  original  condition, etc., complete complying with standard specifications.  (The EWC  and  flushing  tank  with  all  accessories  should  be  got approved  by  the  Executive  Engineer  before  use  on  works) Floor Fitting Each 4974.00
237 Supplying and fixing in position White / Colour Special Delux Model   Glazed   Cascade   Type   Parryware   /   Hindware   / Equivalent  Wall  Mounted  European  Water  Closet  of  best quality  and  approved  make  with  100mm  “P”  or  “S”  trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing,  spun  yarn,  teak  wood  plugs,  brass  screws,  etc., including supplying  and fixing 10 litres  capacity PVC  / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass  nipple  (2  Nos.),  15mm  nylon  connection,  TW  plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and  re-doing  the  dismantled  masonry  to  original  condition, etc., complete complying with standard specifications.  (The EWC  and  flushing  tank  with  all  accessories  should  be  got approved  by  the  Executive  Engineer  before  use  on  works) with  10  litres  capacity  flushing  tank  with  all  internal   dual flush fittings with normal seat cover
Wall Fitting
Each 5830.00
238 Vinyl Flooring 2mm thick sqm. 542.00
239 Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe  of  1.60mm  thick  at  required  locations  to  a  height  of 900mm   from   finished   floor   level   welded   to   38mm   dia Stainless  Steel  pipe  post  of  1.00mm  thick  as  vertical  at 900mm   centre   with   2   Nos.   of  25mm   dia   intermediate horizontal  stainless  steel  pipe of  1.60mm thick  in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS  base  plate  encased  in  the  base  concrete.   The  rate  is inclusive   of   the   charges   for   cutting,   bending,   welding, grinding,   polishing,   conveyance,   electrical   charges,   etc. complete sqm. 5428.00
240 Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless  Steel  pipe  of  1.60mm  thick  will  be  provided  with tubular supports made of 304L Grade Stainless Steel pipe of 25mm  dia  of  1.60mm  thick  welded  to  the  railing.   The supports  will  be  grouted  into  the  wall  and  provided  with 93.00mm  thick  Stainless  Steel  circular  base  plate  of  304 Grade.  The rate shall included for grouting into concrete with necessary  supporting  arrangements  the  hand  rail  in  floor polishing  buffing,  bonding,  cutting,  grinding,  conveyance, welding charges, electrical charges, etc. complete RM 1807.00
241 PVC mould CI Steps for Sump Each 226.00
242 Vertical Blinds    
a Ordinary sqm. 904.00
b Premium sqm. 1357.00
243 Stainless Steel Health Faucet Each 994.00
244 High Density Fibre (HDF) Board sqm. 2168.00
245 Providing and fixing of Aluminium Composite Panel (ACP) 4 sided  having  50  x  25  x  1.50mm  frame  work  vertical  and horizontals   out   of   specially   designed   extruded   sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at  all  level  elevation  and  heights.   The  extruded  section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is – 63400 rate shall included  to  fix  the  main  frame  with  necessary  clamps, fasteners, bolt nuts etc.  The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147.  Rate shall included 4mm thick ACP sheet (0.25
+ 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and  the  ACP  sheet  bounded  with  special  type  structural sealant  of  dow  corning  789  or  equivalent  in  dust  free conditions  the  gaps  between  ACP  sheet  to  be  filed  with whether  sealant  and  backer  rod  or  12mm  foam  sheet  to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer
sqm. 4265.00
246 Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings   for   approval,   supply,   fabricate,   erect   as   per approved  shop  drawings  at  all  floor  levels  and  all  floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got  approved  by  the  Dept.  Officials.)  Design  the  framing system (i.e. male & Female frame) to support vision panels, spandrel  panels  either  with  glass  or  aluminium  composite panel,  openable,  window  panels  on  a  continuous  framing supported  between  floors.  Also  design  the  split  framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass,  groove  width  in  the  system  both  in  horizontal  and vertical shall not be more than 20mm.  Glazing of panel shall be done only at factory at the controlled atmosphere sqm. 4747.00
247 Bitumen Pad    
a 12mm thick sqm. 471.00
b 20mm thick sqm. 705.00
248 Providing Strong Room Door for Sub-Treasuries Each 292900.00
249 Pre-painted Galvanized Iron Windows (Air Tight Model) with Grill and Glass:
Providing  and  fixing  Ajanta  Cave  Model  Window  fabricated from  roll  formed  sections  made  of  galvanized  steel  colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.60mm.
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick finish painted with a  polyester  paint  of  12-16  microns  thick  and  back  coated with alkyd backer of 5-7 microns.
Dimensions of sections: Sections for shutter should be of 46 x  46mm  and  external  frame  should  be  of  46  x  52mm. Section for glass beading should be of 18 x 25mm and centre mullion should be of 46 x 70mm.
Fixing details: The frame and shutter sections should be cut to length and mitre joined with corner bracket made of CRCA electro plated.  Mullion section should be joined with frame / mullion  using  nylon  mullion  cap.   Ethyl  Propylene  Diamine Monomer  (EPD)  Gasket  should  be  used  all  around  glass  in shutter between frame and glazed shutter and both sides of fixed glass.............
sqm. 5400.00
  Accessories:  Handle  made  of  high  grade  aluminium powder coated  and  with  nylon  receiver.   Gaskets  made  of  Ethyl Propylene Diamine Monomer (EPDM).  Corner brackets made of CRCA with zinc phosphating.  Mullion caps made of glass filled nylon.
Glass:  Glass  shutter  and  fixing  glass  portion  should  be provided with a glass of 5mm plain float glass.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4" intervals. Total grill unit should be power coated and fixed to window frame with screws.
The above frame should be fixed to brick / concrete masonry by  using  nylon  self-expanding  caps  and  driving  MS  electro plated 80mm long screws into the caps through frames.
   
250 Pre-painted Galvanized Iron Windows (Semi Air Tight Model) with Grill and Glass:
Providing and fixing Eco 3000 Series Window fabricated from roll formed sections made of galvanized steel colour coated / powder   coated   (Base   steel   as   per   IS   513   'D'   quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick finish painted with a  polyester  paint  of  12-16  microns  thick  and  back  coated with alkyd backer of 5-7 microns.
Dimensions of sections: Sections for frame should be of 48 x 50mm,  section  for  glazed  shutter  frame  should  be  47  x 20mm  and  section  for  fixed  glass  bead  should  be  of  12  x 12mm.
Fixing details: The frame and shutter frame sections should be cut to length and mitre joined with polypropylene corner bracket.   Mullion  section  should  be  joined  with  frame  / mullion  using  nylon  mullion  cap.   Ethyl  Propylene  Diamine Monomer (EPDM) Gasket should be used all around glass in
shutter.
sqm. 5050.00
Accessories: Each glazed shutter should be provided with SS pivot  hinges  -  1  set,  Polypropylene  handle  -  1  No.  with receiver and aluminium peg stay powder coated - 1 No.
Glass:  Glass  shutter  and  fixing  glass  portion  should  be provided with a glass of 4mm Pinhead Glass.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4" intervals. Total grill unit should be power coated and fixed to window frame with screws.
Window Frame should be fixed to brick masonry / concrete masonry by using Nylon self-expanding caps and driving MS electr  oplated  80mm  long  screws  into  the  caps  through frames.
251 Pre-Painted  Galvanized  Iron  Windows  with  Glass,  Grill  &  Fly Mesh:
Providing and fixing Windows from roll formed sections made of galvanized  steel  powder  coated  (Base  steel  as  per  IS  513  'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns.
Dimensions of sections: Section for frame should be of 72mm x 55mm, section for mullion should be of 72mm x 50mm, section for shutter frame should be of 47mm x 20mm, section of fixed glass bead should be of 12mm x 12mm and section for fly mesh shutter frame should be of 40mm x 20mm.
Fixing  details:  Section  for  frame,  glazed  shutters  and  mesh shutters   should   be   cut   to   length   and   mitre   joined   with polypropylene corner brackets, mullion section should be joined with   frame    /   mullion   using   mullion   cap..   Ethyl   Propylene Diamine  Monomer  (EPDM)  Gasket  should  be  used  all  around glass  in shutter  and fixed  glass.  Spoon  profile should  be used around Fly mesh to fix mesh in mesh shutter.
Accessories  :  Each  glazed  shutter  and  mesh  shutter  should  be provided with SS pivot hinges - 1 set, Polypropylene handle - 1
No. with receiver and aluminium powder coated peg stay - 1 No.
sqm. 6660.00
Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass.
Mesh: Mesh shutter should be provided with a SS 32 gauge fly mesh of 304 grades with 144 holes per square inch.
Grill:  Windows  should  be  provided  with  grill  made  of  10mm square  MS  bars  welded  to  5mm  x  12mm  flat  at  4"  intervals. Total  grill  unit  should  be  powder  coated  and  fixed  to  window frame with screws.
Window  frame  should  be  fixed  to  brick  /  concrete  masonry  by using  nylon  self-expanding  caps  and  driving  MS  electro  plated 80mm long screws into the caps through frames.
252 Pre-Painted Galvanized Iron Two Track Sliding Window:  Providing  and  fixing  pre-painted  two  track,  two  panel  sliding system fabricated from roll formed sections made of galvanized steel  powder  coated  (Base  steel  as  per  IS  513  'D'  quality, galvanized as per  IS  277  with zinc  of 120  grams /  sqm.) with total coated thickness of 0.58mm.
Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns.
Dimensions of sections: Section for frame two track should be of 59mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm.
Fixing details: The frame and shutter sections should be cut to length,  joined  with  corner  brackets  made  of  glass  filled  nylon. Ethyl  Propylene  Diamine  Monomer  (EPDM)  Gasket  should  be used all around glass.
Accessories:  Corner  brackets  made  of  glass  filled  nylon  gasket made  of  Ethyl  Propylene  Diamine  Monomer  (EPDM).   Locking system  should  be  of  single  pin  locking  for  Windows.   Single wheel rollers for windows should be provided.
Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass.
Window  frame  should  be  fixed  to  brick  /  concrete  masonry  by using  nylon  self-expanding  caps  and  driving  MS  electro  plated 80mm long screws into the caps through frames.
sqm. 4848.00
253 Pre-Painted Galvanized Iron Three Track Sliding Windows: Providing  and  fixing  pre-painted  three  track,  three  panel sliding system fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 'D' quality, galvanized  as per  IS 277  with zinc  of 120  grams / sqm.) with total coated thickness of 0.58mm.
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick, finish painted with a  polyester  paint  of  12-16  microns  thick  and  back  coated with alkyd backer of 5-7 microns.
Dimensions of sections: Section for outer frame three track should be of 92mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm. Fixing details: The frame and shutter sections should be cut to  length,  joined  with  corner  brackets  made  of  glass  filled nylon.   Ethyl  Propylene  Diamine  Monomer  (EPDM)  Gasket should be used all around glass.
Accessories:  Corner  brackets  made  of  glass  filled  nylon. Gasket made of Ethyl Propylene Diamine Monomer (EPDM). Locking system should be of single pin locking for windows. Single wheel rollers for windows should be provided.
Glass:  Glass  shutter  and  fixed  glass  portion  should  be provided with a glass of 4mm pinhead glass.
Window frame should be fixed to brick / concrete masonry by using  nylon  self-expanding  caps  and  driving  MS  electro plated 80mm long screws into the caps through frames.
sqm. 5353.00
254 Pre-Painted Galvanized Iron Fixed Louvered Ventilators with Glass and Grill:
Providing  and  fixing  louvered  ventilator  fabricated  from  roll formed  sections  made  of  galvanized  steel  colour  coated  / powder   coated   (Base   steel   as   per   IS   513   'D'   quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick, finish painted with a  polyester  paint  of  12-16  microns  thick  and  back  coated with alkyd backer of 5-7 microns.
Dimensions of sections: The section for external frame should be of 57mm x 33mm.
Fixing  details:  The  section  should  be  cut  to  length,  joined with profile to profile component.
Accessories: Glass holding flanges made of glass filled nylon. Glass: Louvers should be provided with 4mm pinhead glass. Grill: Ventilator should be provided with grill made of 10mm Square MS bars to 12mm x 5mm flat at 4" intervals.  Total grill  unit  should  be  powder  coated  and  fixed  to  ventilator frame with screws.
The  above  frames  should  be  fixed  to  brick  /  concrete masonry walls and floor by means of self-expanding screws.
sqm. 4848.00
255 Pre-Painted Galvanized Iron Door Frame:
Providing  and  fixing  door  frames  from  sections  made  of galvanized steel powder coated (Base steel as per IS 513 'D' quality, galvanized  as per  IS 217  with zinc  of 120  grams / sqm.).   The  factory  made  section  should  be  with  a  powder coating of pure polyester powder of 50-60 microns thick with total coated thickness of 1.25mm.  Size of door frame section should  be  of  105  x  60mm  with  a  rebate  of  37mm  to accommodate  35mm thick door shutter.  The frame section should have groove to insert gasket.  2 tie rods of 10mm tor steel to be provided at bottom.  Provision for aldrop, mortise lock  to  be  made  in  the  section  as  per  the  instruction  of Engineer-in-Charge.   The  frame  section  should  be  cut  to length, and joined by way of welding.
Note: 1.25mm thick (Total coated thickness tolerance as per IS 513)
Rm 585.00
256 Pre-Painted Galvanized  Iron windows (Air Tight  Model) with Acrylic Sheet & Grill:
Providing  and  fixing  Ajanta  Cave  Model  window  fabricated from  roll  formed  sections  made  of  galvanized  steel  colour coated / powder coated (Base steel as per IS 513 „D? quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.6mm.
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick, finish painted with a  polyester  paint  of  12-16  microns  thick  and  back  coated with alkyd backer of 5-7 microns.
Dimensions of sections: Sections for shutter should be of 46 x  46mm  and  external  frame  should  be  of  46  x  52mm. Section for glass beading should be of 18 x 25mm and centre mullion should be of 46 x 70mm.
Fixing details: The frame and shutter sections should be cut to length and mitre joined with corner bracket made of CRCA electro plated. Mullion section should be joined with frame / mullion  using  nylon  mullion  cap.    Ethyl  Propylene  Diamine Monomer (EPDM) Gasket should be used all around glass in shutter, between frame and glazed shutter and both sides of fixed glass.
sqm. 5757.00
Accessories:  Handle made of high grade Aluminium Powder coated  and  with  nylon  receiver.    Gaskets  made  of  Ethyl Propylene Diamine Monomer (EPDM).  Corner brackets made of CRCA with zinc phosphating.   Mullion caps made of glass filled nylon.
Glass:  Glass  shutter  and  fixing  glass  portions  should  be provided with a glass of 6mm acrylic sheet.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4” intervals. Total grill unit should be powder coated and fixed to window frame with rivet.  The above frame should be fixed to brick / concrete  masonry  by  using  nylon  self-expanding  caps  and driving  MS  electro  plated  80mm  long  screws  into  the  caps through frames.
257 Structural Glazing:
Providing  and  fixing  structural  glazing  fabricated  from  roll formed  sections  made  of  galvanized  steel  colour  coated (Base steel as per IS 513 of „D? quality, galvanized as per IS
277  with  Zinc  of  120  grams  /  sqm.)  with  total  coated thickness of 0.72mm.  The glass holding section made of 304 grade SS of 0.6mm thick.  Galvanized steel sections are to be used  as  stiffeners  inside  the  colour  coated  steel  /  powder coated  sections  as  per  the  design  requirement.   Design calculations are made to suit wind pressures as given in IS 875.
Paint  specifications:  Primer  coat  with  epoxy  primer  of  5-7 microns thick, finish painted with a polyester paint of 12-16 microns  thick  and  back  coated  with  alkyd  backer  of  5-7 microns or powder coated with pure polyester  powder upto 50-60 microns thick.
Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for  reinforcement  should  be  of  31  x  55mm.  glass  holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x 18mm. Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical   to   slab   as   per   site   requirement.   Polyurethane brackets  should  be  used  to  connect  horizontal  section  to vertical sections.
Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by  using  nylon  self–expanding  cap  and  driving  MS  electro plated 80mm long screws into the caps through frames.
Glass:  5mm reflective Saint Gobain OR equivalent.
sqm. 5757.00
Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical   to   slab   as   per   site   requirement.   Polyurethane brackets  should  be  used  to  connect  horizontal  section  to vertical sections.
Silicone: Natural cure, with good UV resistance to be used. The above frame should be fixed to brick / concrete masonry by  using  nylon  self–expanding  cap  and  driving  MS  electro plated 80mm long screws into the caps through frames.
Glass:  5mm reflective Saint Gobain OR equivalent.
258 Pre-painted Galvanized Iron Fixed Louvered Ventilators with Glass, Mesh and Grill:
Providing  and  fixing  louvered  ventilator  fabricated  from  roll formed  sections  made  of  galvanized  steel  colour  coated  / powder  coated  (Base  Steel  as  per  IS  513  of  „D?  quality, Galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.58 mm
Paint  specification:  Coated  sections  should  be  with  primer coat of epoxy primer of 5-7 microns thick, finish painted with a  polyester  paint  of  12–16  microns  thick  and  black  coated with alkyd backer of 5-7 microns.
Dimensions of section: The section for external frame should be of 57 x 33mm.
Fixing  details:  The  section  should  be  cut  to  length  and joined with profile to profile component.
Accessories: Glass holding flanges made of glass filled nylon. Glass:  Louvers should be provided with 4 mm thick pinhead glass.
Mesh: Mesh should be provided with a SS 32 gauge fly mesh of 304 grades with 144 holes per square Inch.
Grill: Ventilator should be provided with grill made of 10mm square MS bars welded to12mm x 5mm flat at 4” intervals. Total grill unit should be powder coated and fixed to window frame with screws.
The  above  frames  should  be  fixed  to  concrete  /  masonry walls and floor by means of self expanding screws.
sqm. 5151.00
259 Providing   UPVC   (Un-Plasticized   Polyvinyl   Chloride) Door:  Providing  and  fixing  casement  doors  fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which  provides  high  insulation  properties  with  outer frame 60mm x 55mm with an outer wall thickness of 2.4mm.  The window  unit  should  be designed  with  all corner   joints   mitred   and   fusion   welded.   Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement   with   a   thickness   of   1mm   to   have dimensional  stability.  The  sash  should  be  of  60  x 102mm.  The  mullion  should  be  of  60  x  74mm.   The profiles should have co-extruded seals.
Hardware: All the hardware like friction stays, handles should   be   screwed   with   self   tapping   screws.   The handles, locks should be designed so that they cannot be released from outside.
Glazing:  The  window  system  should  be  glazed  with 5mm plain float glass / 6mm bison lam
Installation:  The  profiles  should  be  cut  to  length  and welded  45  degrees.  The  window  should  be  designed such  that  the  water  drainage  does  not  pass  through the   reinforcement   chamber.    The   window   system should  be  fixed  directly  to  the  plastered  brick  wall using   self   expanding   nylon   plug   and   driving   ms electroplated screws into plug.
sqm. 7070.00
260 UPVC Window Specification:
Supplying  and  fixing  UPVC  (Un-Plasticized  Polyvinyl Chloride)  Windows  of casement  type (open)  from  the profile    the  size  of  outer  frame  60mm  x  58mm  and shutter profile are reinforcement with GI/1mm 125GSM and   100%   corrosion   free,   the   profiles   are   multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame  and  shutter  the  shutter  will  be  provided  with Espag multi power point locks and also it operates as handle.  The corners and joints should be welded and cleaned.   Radiations  free  pin  headed  plain  or  brown colour  glass  4mm  thick  should  be  provided  to  the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action,   security   protective   hinges,   strong   locking systems and as per size for arresting noise and energy loss.   The  connecting  mechanism  between  sash  and outer frame that enables opening of the window.  The window should be fixed to the wall with 100% packing with screws and  silicon packing  all  round  the frames. The window should be got approved from the Executive Engineer before use on work
sqm. 6363.00
261 UPVC Ventilator Specification:
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered  Ventilators  of  from  the  profile   the  size  of  outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both  profiles  are   reinforced   with  GI/1mm  125GSM  and 100%   corrosion   free,   the   profile   are   multi   chambered sections  with  wall  thick  of   2mm.   The  EPDM  rubber  (black colour) covered with all over the edges of frame and shutter. The  corners  and  joints  should  be  welded  and  cleaned. Radiations pin headed glass 4mm thick should be provided in the  louvers.   The  window  should  be  fixed  to  the  wall  with 100% packing with screws and silicon packing all round the frames.      The  ventilator  should  be  got  approved  from  the Executive Engineer before use on work
sqm. 6893.00
262 FOAMED PVC DOOR FRAME
Specification:
Providing    factory    made    pre-laminated    FPVC    (Formed Polyvinyl Chloride) Door Frame of the size 105 x 40mm with a wall thickness of 10mm made out of extruded  rigid FPVC profile mitre joined with 6 Nos. of 5mm long screw.  The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3 Nos. to be  provided  for  each  vertical  member,  GI  stiffeners  of  ('U' channel of size 29 x 9, 1mm, 150mm long) - 3 Nos. at hinge point, frame reinforcement of ('U' GI channel of size 46 x 22 x 0.6mm), bottom tie rod of ('U' GI channel size of 15 x 15 x 1mm),    etc.,    complete    complying    with    the    standard specification.  The  door  frame  should  be  got  approved  from the Executive Engineer before use on work
RM 451.00
263 ABS DOOR / EQUIVALENT
Specification:
Providing  of  35mm  thick  factory  made  pre-laminated  ABS (Acrolynitrile  Butadiene  Styrene)  Door  Shutter  moulded  in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by  32  x  32mm  -  2  Nos.,  for  vertical  made  out  of  LVL (Laminated  Veneer  Lumber),  core  material  of  32mm  thick high density craft  paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC  edge  banding  of  size  0.45mm  on  the  vertical  sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for  each  shutter  and  ISI  make  SS  round  lock  complete  for finished item of work, complete complying with the standard specification.  The  door  shutter  and  frame  should  be  got approved from the Executive Engineer before use on work
   
a Plain Pre-laminated Door sqm. 5830.00
b Design Pre-laminated Door sqm. 6150.00
264 Autoclaved Cellular Aerated Concrete Blocks    
a 600mm x 200mm x 100mm Each 44.90
b 600mm x 200mm x 150mm Each 67.40
c 600mm x 200mm x 200mm Each 89.80
d 600mm x 200mm x 225mm Each 101.50
e Self Curing AAC Joint Mortar 40 Kg /
Bag
600.00
f Ready Mix Plaster for Rendering 50 Kg /
Bag
297.90
265 Plasticizer / Super