BUILDING CIVIL ITEMS
S.No | Item Code | Description of items | Unit | Basic Rate for SoR 2019-20 (Rs.) | |
I. SECTION | GLASS MATERIALS (Landing cost – including loading, cost of conveyance & unloading) |
||||
I. SUB- SECTION | PLAIN GLASS PANES | ||||
384 | BMT-I.01 | Plain Float Glass 4 mm thick | 1 sqm | 373 | |
385 | BMT-I.02 | Plain Float Glass 5 mm thick | 1 sqm | 474 | |
386 | BMT-I.03 | Plain Float Glass 6 mm thick | 1 sqm | 593 | |
387 | BMT-I.04 | Plain Float Glass 8 mm thick | 1 Sqm | 789 | |
388 | BMT-I.05 | Plain Float Glass 10 mm thick | 1 Sqm | 830 | |
389 | BMT-I.06 | Plain Float Glass 12 mm thick | 1 Sqm | 996 | |
II. SUB-SECTION | PIN HEADED GLASS PANES | ||||
390 | BMT-I.13 | Pin headed Glass 4 mm thick | 1 sqm | 280 | |
391 | BMT-I.14 | Pin headed Glass 5 mm thick | 1 sqm | 364 | |
III. SUB- SECTION | TINTED GLASS PANES | ||||
392 | BMT-I.07 | Tinted - Bronze/ Green Glass 4 mm thick | 1 sqm | 436 | |
393 | BMT-I.08 | Tinted - Bronze/ Green Glass 5 mm thick | 1 sqm | 545 | |
394 | BMT-I.09 | Tinted - Bronze/ Green Glass 6 mm thick | 1 Sqm | 654 | |
395 | BMT-I.10 | Tinted - Bronze/ Green Glass 8 mm thick | 1 Sqm | 935 | |
396 | BMT-I.11 | Tinted - Bronze/ Green Glass 10 mm thick | 1 Sqm | 1090 | |
397 | BMT-I.12 | Tinted - Bronze/ Green Glass 12 mm thick | 1 Sqm | 1375 | |
IV..SUB- SECTION | FROSTED/ GROUND GLASS PANES | ||||
398 | BMT-I.15 | Frosted / Ground Glass 4 mm thick | 1 sqm | 503 | |
399 | BMT-I.16 | Frosted / Ground Glass 5 mm thick | 1 sqm | 632 | |
V..SUB- SECTION | TOUGHENED PANES | ||||
400 | BMT-I.17 | Toughened Plain Glass 5 mm (including Glass) | 1 sqm | 758 | |
401 | BMT-I.18 | Toughened Plain Glass 6 mm (including Glass) | 1 sqm | 875 | |
402 | BMT-I.19 | Toughened Plain Glass 8 mm (including Glass) | 1 sqm | 1167 | |
403 | BMT-I.20 | Toughened Plain Glass 10 mm (including Glass) | 1 sqm | 1399 | |
404 | BMT-I.21 | Toughened Plain Glass 12 mm (including Glass) | 1 sqm | 1633 | |
J. SECTION | PAINTS & POLISHES (Landing cost – including loading, cost of conveyance & unloading) |
||||
I.SUB- SECTION | PRIMERS, FILLERS & BASES | ||||
405 | BMT-J.01 | Supply of water based Cement Primer of Interior Grade- 1 | 1 Kg | 141 | |
406 | BMT-J.02 | Supply of water based Cement Primer of Exterior Grade- 2 | 1 Kg | 180 | |
407 | BMT-J.31 | Supply of wall putty of White Cement or Polymer or Cement based | 20 Kg | 550 | |
408 | BMT-J.03 | Supply of Red Oxide Primer Paint for iron works of Grade -1 | 1 Litre | 121 | |
409 | BMT-J.04 | Supply of Zinc Chromate Yellow Oxide Primer paint for iron works | 1 Litre | 175 | |
410 | BMT-J.05 | Supply of Wood Primer | 1 Litre | 130 | |
411 | BMT-J.06 | Supply of Metal paste (Putty) for steel works | 1 Kg | 130 | |
412 | BMT-J.07 | Supply of Putty for wood work | 1 Kg | 130 | |
413 | BMT-J.08 | Supply of White Lead | 1 Kg | 93 | |
414 | BMT-J.09 | Supply of Synthetic clear Varnish | 1 Litre | 137 | |
415 | BMT-J.10 | Supply of Spirit | 1 Litre | 96 | |
416 | BMT-J.11 | Supply of Linseed Oil | 1 Litre | 55 | |
417 | BMT-J.12 | Supply of thinner for melamine polish/ french polish | 1 Litre | 131 | |
418 | BMT-J.13 | Supply of thinner for Poly-urethene polish | 1 Litre | 244 | |
419 | BMT-J.14 | Supply of French Polish | 1 Litre | 179 | |
420 | BMT-J.15 | Supply of ready made Wax Polish | 1 Kg | 514 | |
421 | BMT-J.19 | Supply of wood adhesive compound | 1 Kg | 212 | |
422 | BMT-J.27 | Supply of anti-corrosive grade - 1 bitumen paint of black colour | 1 Litre | 465 | |
II.SUB-SECTION | DISTEMPER PAINTS | ||||
423 | BMT-J.20 | Supply of Dry Powder Distemper | 1 Kg | 40 | |
424 | BMT-J.21 | Supply of acrylic based Oil Bound washable Distemper | 1 Kg | 81 | |
425 | BMT-J.26 | Supply of paint grade white lime for wash | 25 Kg | 490 | |
426 | BMT-J.23 | Supply of Water proof Cement paint | 1 Kg | 49 | |
427 | BMT-J.25 | Supply of water proof Cement paint pack | 25 Kg | 1009 | |
III.SUB-SECTION | EMULSION BASED PAINTS | ||||
428 | BMT-J.24 | Supply of acrylic emulsion paint interior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter. | 1 Litre | 168 | |
429 | BMT-J.34 | Supply of acrylic emulsion paint exterior grade with silicon additives having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. | 1Lit | 194 | |
430 | BMT-J.35 | Supply of acrylic emulsion paint weather proof water- based, modified acrylic with silicon additives exterior grade having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. | 1Lit | 214 | |
IV.SUB-SECTION | SOLVENT BASED PAINTS | ||||
431 | BMT-J.22 | Supply of synthetic polymer luxury plastic emulsion paint of superior grade having VOC (Volatile Organic Compound) content less than 50 grams/ liter. | 1 Litre | 404 | |
V.SUB-SECTION | OIL BASED ENAMEL PAINTS | ||||
432 | BMT-J.29 | Supply of ready mixed Synthetic Enamel paints in all shades Grade - I having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. | 1 Litre | 248 | |
433 | BMT-J.30 | Supply of ready mixed Synthetic Enamel paints in all shades Grade - II having VOC (Volatile Organic Compound ) content less than 50 grams/ liter. | 1 Litre | 172 | |
VI.SUB-SECTION | TEXTURE PAINTS | ||||
434 | BMT-J.32 | Exterior Texture. | 25 Kg | 818 | |
435 | BMT-J.33 | Gold line Exterior Texture | 25 Kg | 1060 | |
VII.SUB- SECTION | SPECIAL PAINTS | ||||
436 | BMT-J.16 | Supply of Melamine Polish | 1 Litre | 314 | |
437 | BMT-J.17 | Supply of Interior Grade Poly-Urethene Polish | 1 Litre | 637 | |
438 | BMT-J.18 | Supply of Exterior Grade Poly-Urethene Polish | 1 Litre | 708 | |
439 | BMT-J.28 | Supply of grade-1 aluminium paint | 1 Litre | 255 | |
440 | BMT-J.36 | Acrylic spray plaster in paste form made with specially selected inert mineral fillers, antifungal agents to protect the material the acrylic binding medium used gives good surface adhesion any grade Spray Plaster - Superfine (Interior Grade) | 25Kg | 500 | |
441 | BMT-J.37 | Acrylic coarse spray plaster in paste form made with specially selected inert mineral fillers, antifungal agents to protect the material the acrylic binding medium used gives good surface adhesion interior gradeAcrylic coarse | 25Kg | 400 | |
442 | BMT-J.38 | Supply of acrylic emulsion paint interior premium grade having VOC (Volatile Organic Compound) content less than 50 grams/liter | 1 Liter | 200 | |
443 | BMT-J.39 | Supply of Base coat as primer for natural textures and natural stone based paints - Exterior GradeBASE COAT | 1Kg | 61 | |
444 | BMT-J.40 | Acrylic spray plaster in paste form made with specially selected inert mineral fillers, antifungal agents to protect the material the acrylic binding medium used gives good surface adhesion exterior grade Spray Plaster (Exterior) | 25Kg | 1300 | |
445 | BMT-J.41 | Supply of acrylic emulsion paint exterior premium grade with silicon additives having VOC (Volatile Organic Compound) content less than 50 grams/liter.Alltimate | 1 Liter | 310 | |
K. SECTION | PARTICLE BOARDS (Landing cost – including loading, cost of conveyance, unloading) |
||||
I.SUB- SECTION | MELAMINE FACED PLAIN PARTICLE BOARDS | ||||
446 | BMT-K.01 | Melamine faced Single Deco PPB- 8 mm thick | 1Sqm | 590 | |
447 | BMT-K.02 | Melamine faced Single Deco PPB- 12 mm thick | 1Sqm | 670 | |
448 | BMT-K.03 | Melamine faced Single Deco PPB- 18 mm thick | 1Sqm | 776 | |
449 | BMT-K.04 | Melamine faced Single Deco PPB- 25 mm thick | 1Sqm | 879 | |
450 | BMT-K.05 | Melamine faced Single Deco PPB- 35 mm thick | 1 Sqm | 1463 | |
451 | BMT-K.06 | Melamine faced Twin Deco PPB- 8 mm thick | 1 Sqm | 679 | |
452 | BMT-K.07 | Melamine faced Twin Deco PPB- 12 mm thick | 1 Sqm | 776 | |
453 | BMT-K.08 | Melamine faced Twin Deco PPB-18 mm thick | 1 Sqm | 898 | |
454 | BMT-K.09 | Melamine faced Twin Deco PPB-25 mm thick | 1 Sqm | 995 | |
455 | BMT-K.10 | Melamine faced Twin Deco PPB-35 mm thick | 1 Sqm | 1869 | |
II.SUB- SECTION | INSULATING PARTICLE BOARDS | ||||
456 | BMT-K.11 | Natural Colour-Insulating Board - 12 mm thick | 1 Sqm | 242 | |
457 | BMT-K.12 | Natural Colour-Insulating Board - 18 mm thick | 1 Sqm | 358 | |
458 | BMT-K.13 | Natural Colour-Insulating Board - 25 mm thick | 1 Sqm | 414 | |
459 | BMT-K.14 | White Insulating Board - 12 mm thick | 1 Sqm | 268 | |
460 | BMT-K.15 | White Insulating Board - 18 mm thick | 1 Sqm | 383 | |
461 | BMT-K.16 | White Insulating Board - 25 mm thick | 1 Sqm | 341 | |
III.SUB- SECTION | MEDIUM DENSITY FIBRE BOARD | ||||
462 | BMT-K.17 | Medium Fibre Board: Interior Grade - 6 mm thick | 1 Sqm | 359 | |
463 | BMT-K.18 | Medium Fibre Board: Interior Grade - 8 mm thick | 1 Sqm | 407 | |
464 | BMT-K.19 | Medium Fibre Board: Interior Grade - 12 mm thick | 1 Sqm | 545 | |
465 | BMT-K.20 | Medium Fibre Board: Interior Grade - 15 mm thick | 1 Sqm | 693 | |
466 | BMT-K.21 | Medium Fibre Board: Interior Grade - 18 mm thick | 1 Sqm | 773 | |
467 | BMT-K.22 | Medium Fibre Board: Interior Grade - 25 mm thick | 1 Sqm | 1208 | |
468 | BMT-K.23 | Medium Fibre Board: Interior Grade - 30 mm thick | 1 Sqm | 1460 | |
469 | BMT-K.24 | Medium Fibre Board: Interior Grade - 35 mm thick | 1 Sqm | 1592 | |
470 | BMT-K.25 | Medium Fibre Board: Exterior Grade - 6 mm thick | 1 Sqm | 488 | |
471 | BMT-K.26 | Medium Fibre Board: Exterior Grade - 8 mm thick | 1 Sqm | 569 | |
472 | BMT-K.27 | Medium Fibre Board: Exterior Grade - 12 mm thick | 1 Sqm | 753 | |
473 | BMT-K.28 | Medium Fibre Board: Exterior Grade - 15 mm thick | 1 Sqm | 946 | |
474 | BMT-K.29 | Medium Fibre Board: Exterior Grade - 18 mm thick | 1 Sqm | 1059 | |
475 | BMT-K.30 | Medium Fibre Board: Exterior Grade - 25 mm thick | 1 Sqm | 1411 | |
476 | BMT-K.31 | Medium Fibre Board: Exterior Grade - 30 mm thick | 1 Sqm | 1758 | |
477 | BMT-K.32 | Medium Fibre Board: Exterior Grade - 35 mm thick | 1 Sqm | 2077 | |
478 | BMT-K.33 | MDF Board: Plain-Interior - 9 mm thick | 1 Sqm | 346 | |
479 | BMT-K.34 | MDF Board: Plain-Interior - 12 mm thick | 1 Sqm | 393 | |
480 | BMT-K.35 | MDF Board: Plain-Interior - 18 mm thick | 1 Sqm | 487 | |
481 | BMT-K.36 | MDF Board: Plain-Interior - 25 mm thick | 1 Sqm | 584 | |
482 | BMT-K.37 | MDF Board: Plain-Interior - 30 mm thick | 1 Sqm | 890 | |
483 | BMT-K.38 | MDF Board: Plain-Interior - 35 mm thick | 1 Sqm | 1053 | |
484 | BMT-K.39 | MDF Board: Plain-Exterior - 9 mm thick | 1 Sqm | 431 | |
485 | BMT-K.40 | MDF Board: Plain-Exterior - 12 mm thick | 1 Sqm | 487 | |
486 | BMT-K.41 | MDF Board: Plain-Exterior - 18 mm thick | 1 Sqm | 639 | |
487 | BMT-K.42 | MDF Board: Plain-Exterior - 25 mm thick | 1 Sqm | 801 | |
488 | BMT-K.43 | MDF Board: Plain-Exterior - 30 mm thick | 1 Sqm | 1053 | |
489 | BMT-K.44 | MDF Board: Plain-Exterior - 35 mm thick | 1 Sqm | 1213 | |
490 | BMT-K.45 | MDF Board: Interior-One Side Laminated -9 mm thick | 1 Sqm | 542 | |
491 | BMT-K.46 | MDF Board: Interior-One Side Laminated -12 mm thick | 1 Sqm | 613 | |
492 | BMT-K.47 | MDF Board: Interior-One Side Laminated -18 mm thick | 1 Sqm | 713 | |
493 | BMT-K.48 | MDF Board: Interior-One Side Laminated -25 mm thick | 1 Sqm | 801 | |
494 | BMT-K.49 | MDF Board: Interior-One Side Laminated -30 mm thick | 1 Sqm | 1158 | |
495 | BMT-K.50 | MDF Board: Interior-One Side Laminated -35 mm thick | 1 Sqm | 1235 | |
496 | BMT-K.51 | MDF Board: Exterior-One Side Laminated -9 mm thick | 1 Sqm | 623 | |
497 | BMT-K.52 | MDF Board: Exterior-One Side Laminated -12 mm thick | 1 Sqm | 700 | |
498 | BMT-K.53 | MDF Board: Exterior-One Side Laminated -18 mm thick | 1 Sqm | 793 | |
499 | BMT-K.54 | MDF Board: Exterior-One Side Laminated -25 mm thick | 1 Sqm | 927 | |
500 | BMT-K.55 | MDF Board: Exterior-One Side Laminated -30 mm thick | 1 Sqm | 1235 | |
501 | BMT-K.56 | MDF Board: Exterior-One Side Laminated -35 mm thick | 1 Sqm | 1312 | |
502 | BMT-K.57 | MDF Board: Interior-Both Side Laminated -9 mm thick | 1 Sqm | 590 | |
503 | BMT-K.58 | MDF Board: Interior-Both Side Laminated -12 mm thick | 1 Sqm | 700 | |
504 | BMT-K.59 | MDF Board: Interior-Both Side Laminated -18 mm thick | 1 Sqm | 801 | |
505 | BMT-K.60 | MDF Board: Interior-Both Side Laminated -25 mm thick | 1 Sqm | 1006 | |
506 | BMT-K.61 | MDF Board: Interior-Both Side Laminated -30 mm thick | 1 Sqm | 1235 | |
507 | BMT-K.62 | MDF Board: Interior-Both Side Laminated -35 mm thick | 1 Sqm | 1312 | |
508 | BMT-K.63 | MDF Board: exterior-Both Side Laminated -9 mm thick | 1 Sqm | 666 | |
509 | BMT-K.64 | MDF Board: exterior-Both Side Laminated -12 mm thick | 1 Sqm | 792 | |
510 | BMT-K.65 | MDF Board: exterior-Both Side Laminated -18 mm thick | 1 Sqm | 937 | |
511 | BMT-K.66 | MDF Board: exterior-Both Side Laminated -25 mm thick | 1 Sqm | 1024 | |
512 | BMT-K.67 | MDF Board: exterior-Both Side Laminated -30 mm thick | 1 Sqm | 1296 | |
513 | BMT-K.68 | MDF Board: exterior-Both Side Laminated -35 mm thick | 1 Sqm | 1390 | |
IV.SUB- SECTION | CEMENT BONDED PARTICLE BOARD | ||||
514 | BMT-K.69 | Cement bonded particle board conforming to IS 14276- 6 mm thick | 1 sqm | 233 | |
515 | BMT-K.70 | Cement bonded particle board conforming to is 14276- 8 mm thick | 1 sqm | 311 | |
516 | BMT-K.71 | Cement bonded particle board conforming to is 14276- 10 mm thick | 1 sqm | 390 | |
517 | BMT-K.72 | Cement bonded particle board conforming to is 14276- 12 mm thick | 1 sqm | 479 | |
518 | BMT-K.73 | Cement bonded particle board conforming to is 14276- 16 mm thick | 1 sqm | 633 | |
519 | BMT-K.109 | Cement bonded particle board conforming to is 14276- 18 mm thick | 1 Sqm | 672 | |
520 | BMT-K.74 | Cement bonded particle board conforming to is 14276- 20 mm thick | 1 sqm | 771 | |
521 | BMT-K.75 | Cement bonded particle board conforming to is 14276- 25 mm thick | 1 sqm | 921 | |
522 | BMT-K.76 | Cement bonded particle board conforming to is 14276- 30 mm thick | 1 sqm | 1119 | |
523 | BMT-K.77 | Cement bonded particle board conforming to is 14276- 40 mm thick | 1 sqm | 1495 | |
524 | BMT-K.78 | Pre laminated cement bonded particle board-6 mm thick | 1 sqm | 498 | |
525 | BMT-K.79 | Pre laminated cement bonded particle board-8 mm thick | 1 sqm | 545 | |
526 | BMT-K.80 | Pre laminated cement bonded particle board- 10 mm thick | 1 sqm | 583 | |
527 | BMT-K.81 | Pre laminated cement bonded particle board- 12 mm thick | 1 sqm | 671 | |
528 | BMT-K.82 | Pre laminated cement bonded particle board- 16 mm thick | 1 sqm | 714 | |
529 | BMT-K.83 | Cement Bonded Particale DESIGNER BOARD Available Designs 1. Lumber 2. Quadra 3. Murk Standard size 8?X4? 10?X4?- 6mm thick |
1 sqm | 286 | |
530 | BMT-K.84 | Cement Bonded Particale DESIGNER BOARD Available Designs 1. Lumber 2. Quadra 3. Murk Standard size 8?X4? 10?X4?- 8mm thick |
1 sqm | 346 | |
531 | BMT-K.85 | Cement Bonded Particale DESIGNER BOARD Available Designs 1. Lumber 2. Quadra 3. Murk Standard size 8?X4? 10?X4?- 10mm thick |
1 sqm | 425 | |
532 | BMT-K.86 | Cement Bonded Particale DESIGNER BOARD Available Designs 1. Lumber 2. Quadra 3. Murk Standard size 8?X4? 10?X4?- 12mm thick |
1 sqm | 523 | |
533 | BMT-K.87 | Cement Bonded Particale DESIGNER BOARD Available Designs 1. Lumber 2. Quadra 3. Murk Standard size 8?X4? 10?X4?- 16mm thick |
1 sqm | 691 | |
534 | BMT-K.88 | Cement Bonded Board conforming to IS:14862-2000 - 4mm Thick | 1 Sqm | 146 | |
535 | BMT-K.89 | Cement Bonded Board conforming to IS:14862-2000 - 6mm Thick | 1 Sqm | 209 | |
536 | BMT-K.90 | Cement Bonded Board conforming to IS:14862-2000 - 8mm Thick | 1 Sqm | 269 | |
537 | BMT-K.91 | Cement Bonded Board conforming to IS:14862-2000 - 10mm Thick | 1 Sqm | 309 | |
538 | BMT-K.92 | Cement Bonded Board conforming to IS:14862-2000 - 12mm Thick | 1 Sqm | 386 | |
539 | BMT-K.93 | Cement Bonded Board conforming to IS:14862-2000 - 14mm Thick | 1 Sqm | 410 | |
540 | BMT-K.94 | Cement Bonded Board conforming to IS:14862-2000 - 16mm Thick | 1 Sqm | 490 | |
541 | BMT-K.95 | Cement Bonded Board conforming to IS:14862-2000 - 18mm Thick | 1 Sqm | 529 | |
542 | BMT-K.96 | Cement Bonded Board conforming to IS:14862-2000 - 20mm Thick | 1 Sqm | 590 | |
543 | BMT-K.105 | ITEM DELETED | |||
544 | BMT-K.106 | 50 mm thick SOLID WALL PANEL Sandwich panels made of light weight FRACC non-asbestos fibre reinforced cement concrete | 1 Sqm | 907 | |
545 | BMT-K.107 | 75 mm thick SOLID WALL PANEL Sandwich panels made of light weight FRACC non-asbestos fibre reinforced cement concrete | 1 Sqm | 1143 | |
Note: Items BMT-K.97 , BMT-K.98,BMT-K.99,BMT-K.100,BMT-K.101,BMT- K.102,BMT-K.103,BMT-K.104 are removed in the section K and are brought as new items in the Section L as BMT-L.21,BMT-L.22,BMT-L.23,BMT-L.24,BMT- L.25,BMT-L.26,BMT-L.27,BMT-L.28. | |||||
L. SECTION | PLYWOOD (Landing cost – incuding loading, cost of conveyance, unloading) |
||||
546 | I.SUB- SECTION | MOISTURE RESISTANT (MR) GRADE | |||
547 | BMT-L.01 | 3 Ply - 4 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 363 | |
548 | BMT-L.02 | 5 Ply - 6 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 399 | |
549 | BMT-L.03 | 5 Ply - 8 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 480 | |
550 | BMT-L.04 | 5 Ply - 9 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 480 | |
551 | BMT-L.05 | 9 Ply - 12 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 600 | |
552 | BMT-L.06 | 9 Ply - 15 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 885 | |
553 | BMT-L.07 | 9 Ply - 18 mm thick Plywood(IS:303) MR Grade | 1 Sqm | 867 | |
II.SUB- SECTION | BOILING WATER RESISTANT (BWR) GRADE | ||||
554 | BMT-L.08 | 3 Ply - 4 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 423 | |
555 | BMT-L.09 | 5 Ply - 6 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 472 | |
556 | BMT-L.10 | 5 Ply - 8 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 588 | |
557 | BMT-L.11 | 5 Ply - 9 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 554 | |
558 | BMT-L.12 | 9 Ply - 12 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 725 | |
559 | BMT-L.13 | 9 Ply - 15 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 1031 | |
560 | BMT-L.14 | 9 Ply - 19 mm thick Plywood(IS:303) BWR/BWP Grade | 1 Sqm | 1044 | |
III.SUB- SECTION | VENEERED DECORATIVE PLYWOOD | ||||
561 | BMT-L.15 | 3 Ply-4 mm thick One side Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 561 | |
562 | BMT-L.16 | 5 Ply - 6 mm thick One side Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 731 | |
563 | BMT-L.17 | 5 Ply - 9 mm thick One side Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 894 | |
564 | BMT-L.18 | 9 Ply - 13 mm thick One side Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 1193 | |
565 | BMT-L.19 | 5 Ply - 9 mm thick Both sides Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 1221 | |
566 | BMT-L.20 | 9 Ply - 12 mm thick Both sides Teak Veneer Decorated Plywood (IS:1328) | 1 Sqm | 1359 | |
IV.SUB- SECTION | LAMINATES | ||||
567 | BMT-L.21 | Laminate Sheets - Glossy Finish: 1 mm thick | 1 Sqm | 367 | |
568 | BMT-L.22 | Laminate Sheets - Glossy Finish: 1.50 mm thick | 1 Sqm | 524 | |
569 | BMT-L.23 | Laminate Sheets - Glossy Finish: 1.80 mm thick | 1 Sqm | 575 | |
570 | BMT-L.24 | Laminate Sheets - Mat Finish: 1 mm thick | 1 Sqm | 370 | |
571 | BMT-L.25 | Laminate Sheets - Mat Finish: 1.50 mm thick | 1 Sqm | 516 | |
572 | BMT-L.26 | Laminate Sheets - Mat Finish: 1.80 mm thick | 1 Sqm | 555 | |
V.SUB- SECTION | COMMERCIAL VENEERS | ||||
573 | BMT-L.27 | Teak Veneer Lamination - 4 mm thick - Pencil Grains | 1 Sqm | 410 | |
574 | BMT-L.28 | Teak Veneer Lamination - 4 mm thick - Natural Grains | 1 Sqm | 717 | |
575 | BMT-L.29 | Providing Wood Polymer Composite (WPC) solid, frostywhite single extruded factory made 2.44 mt x 1.22 mt boards in | |||
576 | BMT-L.29.A | 6 MM thickness (Density 550 kg/Cum, Weight 9.5Kg) | sqmt | 630 | |
577 | BMT-L.29.B | 11 MM thickness (Density 500 kg/Cum, Weight 16.5Kg) | sqmt | 1080 | |
578 | BMT-L.29.C | 18 MM thickness (Density 650 kg/Cum, Weight 35Kg) | sqmt | 2145 | |
M. SECTION | CEILINGS, WALL PARTITIONS & WALL LININGS | ||||
I.SUB- SECTION | FALSE CEILINGs- TILES / SHEETS | ||||
579 | BMT-M.01 | Gypsum Board tiles of size notless than 0.595 M x 0.595 M of 12.5 mm thick as per IS 2095 -1992 | 1 Sqm | 238 | |
580 | BMT-M.02 | Gypsum Board tiles of size notless than 0.595 M x 0.595 M of 9 mm thick as per IS 2095 -1992 | 1 Sqm | 232 | |
581 | BMT-M.03 | Gypsum Board Plain sheet 12.5 mm thick as per IS 2095 -1993 | 1 Sqm | 210 | |
582 | BMT-M.28 | 14 mm - Mineral Fiber sheet 600 x 600 of Board / Tegular Edge tiles with a Humidity Resistance of 80% RH, Average NRC 0.50, Light Reflectance >80%, Thermal Conductivity λ = 0.052 to 0.057 w/mk, Fire Performance Class 0/Class 1 | 1 Sqm | 524 | |
583 | BMT-M.29 | 15 mm - Mineral Fiber sheet 600 x 600 of Board / Tegular Edge tiles with a Humidity Resistance of 90% RH, Average NRC 0.50, Light Reflectance >80%, Thermal Conductivity λ = 0.052 to 0.057 w/mk, Fire Performance Class 0/Class 1 | 1 Sqm | 614 | |
584 | BMT-M.30 | 16 mm - Tegular Edge 600 x 600 of Board / Tegular/ Micro look Edge tiles with a Humidity Resistance of 99% RH, Average NRC 0.60, Light Reflectance >88%, Thermal Conductivity λ = 0.052 to 0.057 w/mk, Fire Performance Class 0/Class 1 | 1 Sqm | 661 | |
585 | BMT-M.31 | 12 mm - Mineral Fiber sheet 600 x 600 (Square / Tegular) Edge tiles | 1 Sqm | 406 | |
586 | BMT-M.36 | Supply of Thermocole 12 mm thick sheets | 1 Sqm | 24 | |
587 | BMT-M.37 | Supply of Thermocole 19 mm thick sheets | 1 Sqm | 41 | |
588 | BMT-M.40 | Calcium Silicate Boards - 6mm thick | 1 Sqm | 198 | |
589 | BMT-M.41 | Calcium Silicate Boards - 8mm thick | 1 Sqm | 263 | |
590 | BMT-M.42 | Calcium Silicate Boards - 10mm thick | 1 Sqm | 330 | |
591 | BMT-M.43 | Calcium Silicate Boards - 12mm thick | 1 Sqm | 395 | |
592 | BMT-M.51 | Supplying and fixing of false ceiling using Plaster of paris Boards 12 mm thick with standard GI ceiling angles, sections perimeter channels including cost and conveyance of all materials and labour charges etc complete | 1 Sqm | 405 | |
593 | BMT-M.52 | Supplying and fixing of false ceiling using Plaster of paris Boards 10 mm thick with standard GI ceiling angles, sections perimeter channels including cost and conveyance of all materials and labour charges etc complete | 1 Sqm | 338 | |
594 | BMT-M.53 | Designer ceiling Cement Boards -thickness 3.2 mm | 1 Sqm | 212 | |
595 | BMT-M.54 | High pressure steam cured Cement Boards 4 mm thick | 1 Sqm | 113 | |
596 | BMT-M.55 | High pressure steam cured Cement Boards 6 mm thick | 1 Sqm | 170 | |
597 | BMT-M.56 | High pressure steam cured Cement Boards 8 mm thick | 1 Sqm | 225 | |
598 | BMT-M.57 | High pressure steam cured Cement Boards 10 mm thick | 1 Sqm | 283 | |
599 | BMT-M.58 | High pressure steam cured Cement Boards 12 mm thick | 1 Sqm | 339 | |
600 | BMT-M.59 | High pressure steam cured Cement Boards 14 mm thick | 1 Sqm | 395 | |
601 | BMT-M.60 | High pressure steam cured Cement Boards 16 mm thick | 1 Sqm | 452 | |
602 | BMT-M.61 | High pressure steam cured Cement Boards 18 mm thick | 1 Sqm | 508 | |
603 | BMT-M.62 | High pressure steam cured Cement Boards 20 mm thick | 1 Sqm | 564 | |
604 | BMT-M.63 | High pressure steam cured designer Cement Boards 4 mm thick | 1 Sqm | 166 | |
605 | BMT-M.64 | High pressure steam cured designer Cement Boards 6 mm thick | 1 Sqm | 245 | |
606 | BMT-M.70 | Supply and fixing of CEMENT BONDED PARTICLE BOARDS (IS 14276) false ceiling using 8MM CEMENT BONDED PARTICLE BOARDS with galvanized and pre painted steel T section of size 24mm x 38mm x 0.3 mm for main T duty pre punched to accept cross T section of size 24mm x 30mm x 0.3 mm duly punched at both ends for insertion into main T. The grid size will be 610mm x 610mm. The frame work (grid) is suspended to the roof by using G.I flat of 0.60mm or 14-gauge G.I wire with necessary fixers to the roof and frame work. CEMENT BONDED PARTICLE BOARDS lay on the grid. The cost inclusive of necessary hardware, labor, one coat of primer (Both side) and two coats of smooth finish on visible side. | 1 Sqm | 924 | |
607 | BMT-M.79 | Providing and fixing false ceiling consisting of 600mm X 600mm, Solid PVC insulation panels having wall thickness of 1mm thick plain PVC rigid foam sheet and EPS as defined in of desired thickness depending on insulation required shall be insert in a frame work made using anodized aluminium Tee section of sizes 1”X1” (25X25mm, 19 gauge or 1mm thick) in square pattern of grid sizes of 2?X2? (600X600mm). The aluminium framework is supported from the ceiling with the help of G.I. hook and G.I. wire/6mm.M.S. rods of required sizes to maintain proper level etc. the aluminium framework is supported on side wall with the use of aluminium 1”X1” (25X25mm) angles, complete as per direction of Engineer-in-Charge, manufacture?s specification & drawing | 1 Sqm | 1179 | |
608 | BMT-M.80 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 13 mm thick Square Edge - Fissura Fine Model | 1 Sqm | 321 | |
609 | BMT-M.81 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 13 mm thick Square Edge - Speckle Model | 1 Sqm | 359 | |
610 | BMT-M.82 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 13 mm thick Square Edge - Textura Model | 1 Sqm | 397 | |
611 | BMT-M.83 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 15 mm thick Standard Regular Edge | 1 Sqm | 406 | |
612 | BMT-M.84 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 15 mm thick Fissura Fine Model | 1 Sqm | 416 | |
613 | BMT-M.85 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 15 mm thick Speckle Model | 1 Sqm | 434 | |
614 | BMT-M.86 | Mineral Fibre Ceiling Tile of 0.595 mm x 0.595 mm of 15 mm thick Textura Model | 1 Sqm | 471 | |
615 | BMT-M.87 | Supply and fixing of PVC false ceiling on MS/GI made skeleton framework. The frame shall be 24 X 48mm MS tube section fixed along with the wall. The entire frame work shall be concealed with PVC section having overall dimensions of 6 X 250mm with a wall thickness of 1mm ± 0.3mm with tongue and groove system, provided with necessary arrangements for electrical connections, complete, for finished item of work. | 1 Sqm | 1308 | |
II.SUB- SECTION | FALSE CEILINGs- SECTIONS & ACCESSORIES | ||||
616 | BMT-M.04 | G.I. Ceiling Angle - 25 mm x 10 mm x 0.55 mm | 1 RM | 63 | |
617 | BMT-M.05 | G.I. Ceiling Section 51.5 mm x 26 mm x 10.5 mm x 0.55 mm thick | 1 RM | 72 | |
618 | BMT-M.06 | G.I. Intermediate Section 45 mm x 15 mm x 15 mm x 0.9 mm | 1 RM | 71 | |
619 | BMT-M.07 | G.I. Perimeter Channel - 20 mm x 27 mm x 30 mm (web) of 0.55 mm thick | 1 RM | 63 | |
620 | BMT-M.08 | G.I.-Precoated Fine line Grid 25 mm x 25 mm x 0.7 mm | 1 RM | 35 | |
621 | BMT-M.09 | G.I.-Precoated Fine line Grid 15 mm x 25 mm x 0.7 mm | 1 RM | 31 | |
622 | BMT-M.10 | GI - Precoated - T-Sec- 24 mm x 38 mm x 0.7 mm thick | 1 RM | 46 | |
623 | BMT-M.11 | Hot dipped GI Angle - Precoated - Grid: 19 mm x 19 mm | 1 RM | 34 | |
624 | BMT-M.12 | Polyester painted GI - T Section - 24 x 32 mm | 1 RM | 42 | |
625 | BMT-M.13 | Polyester painted GI - T Section - 24 x 25 mm | 1 RM | 38 | |
626 | BMT-M.14 | Polyester painted GI - T Section - 24 mm x 27 mm | 1 RM | 39 | |
627 | BMT-M.15 | Aluminium Angle : 24 mm x 24 mm | 1 RM | 24 | |
628 | BMT-M.16 | Anodised Aluminium T Section : 24 x 24.5 x 2.4 mm | 1 RM | 29 | |
629 | BMT-M.17 | Connecting Clips | 1 Each | 3 | |
630 | BMT-M.18 | Rawl Plug | 1 Each | 2 | |
631 | BMT-M.19 | 6 mm Nylon Rawl Plug | 1 Each | 4 | |
632 | BMT-M.20 | Soffit Cleats | 1 Each | 3 | |
633 | BMT-M.21 | Drywall Screws - 25 mm | 1 Each | 2 | |
634 | BMT-M.22 | Jointing Compound | 1 Kg | 25 | |
635 | BMT-M.23 | Jointing Paper Tape | 1 RM | 4 | |
636 | BMT-M.24 | Drywall Top Coat | 1 Litre | 120 | |
637 | BMT-M.25 | Universal Holding Clips | 1 Each | 3 | |
638 | BMT-M.26 | 4 mm Dia GI Connecting Rod | 1 RM | 11 | |
639 | BMT-M.27 | 2 mm Dia GI Connecting Rod | 1 RM | 8 | |
III.SUB- SECTION | WALL PANELLS & WALL LININGS | ||||
640 | BMT-M.39 | Providing wooden panelling 12 mm thick one side laminated sheet fixed on wooden frame of BT wood size 50.8 mm x 25.4 mm (2"x1") at distance of 609.6mm (2'-0") intervals of both ways providing 3/4" x 1/2" (19.05 mm x 12.7 mm) size BT wood ornamental cover beading and necessary screws, fevicol glue complete for finished item of work. | 1 Sqm | 1405 | |
641 | BMT-M.32 | Perforated wall panels channeled wood works sheets of width 128 mm, thickness of 16mm and length 2440 mm made of a high density particle board substrate with a laminated facing as per the approved shade /Species & Finish and a melamine balancing layer on the reverse side, with a special perforation pattern fluted perforation on the visible surface with a minimum sag resistance of RH90 and a fire rating class of 1 as per Part 7 of BS 476 with a “tongue-and-grooved” edges and the back of the perforated panel is with sound absorbing non-woven acoustical fleece | 1 Sqm | 2318 | |
642 | BMT-M.65 | Supply and fixing of wall panelling (water, fire and Termite proof) with frame work made of GI stud profile of size 48 x 40x10 x 0.6 mm thick placed at every 610 mm C/C intervals fixed vertically in between floor and roof `U? track of size 50 x 30 x 0.6 mm thick duly fixed with self expansion screws and with 8 mm thick E-board / 6 mm thick E-board classic cladded around with self tapping self embedding screws fixed at every 300 mm (centres) leaving a 3 mm gap between two panels of width 2?-0”. The Gap will be covered with a decorative beading. Surface will be given a smooth finish over a coat of primer. - With 8 mm Designer CEMEMT BONDED BOARD | 1 Sqm | 816 | |
643 | BMT-M.66 | ITEM DELETED | |||
644 | BMT-M.71 | Supply and fixing CEMENT BONDED PARTICLE BOARDS(IS 14276) wall paneling using 10 MM CEMENT BONDED PARTICLE BOARDS with frame work made of GI stud section of size 48mm x 35mm x 0.55mm thick placed at every 610 mm C/C intervals vertically and at 1200mm internals horizontally fixed to the wall by means of self expansion screws and caps. CEMENT BONDED PARTICLE BOARDS is to be fixed to frame by means of self taping screws placed at every 300 mm intervals leaving 3mm gap between two panels. The cost inclusive of one coat o primer and two coats of smooth finish and cost & conveyance of all materials, labor charges etc. complete as per the direction of Engineer in charge. | 1 Sqm | 1161 | |
645 | BMT-M.74 | Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS wall paneling using 12 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS with frame work made of G.I stud section of size 48mm x 35mm x 0.55mm thick placed at every 610mm intervals vertically and at 1200mm internals horizontally fixed to the wall by means of self expansion screws and caps. LAM is to be fixed to frame by means of self-taping screws placed at every 300mm intervals leaving 3mm gap between two panels. The cost inclusive of Conveyance of materials, Labor charges etc., complete as per the direction of Engineer in charge | 1 Sqm | 1763 | |
646 | BMT-M.77 | Providing and fixing INSULATED PVC WALL PANELING shall consist of PVC insulated panels having wall thickness of 1mm /1.5mm/2mm PVC sheet and the desired thickness of EPS (dependent on the insulation required) screwed into the wall using screws of adequate length. The screws shall be placed at a distance of 150mm and shall be 25mm from the edge of the insulated panel on all from sides of the panel. The PVC strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck using solvent cement adhesive at the places where two panels are joined, so a to cover the screw of both the panels, using solvent cement. 90 heat bent strips of 5mm thick PVC sheets of width 75mm X75mm feathered at the edges shall be stuck at wall joints / pillars etc. , complete as per direction of Engineer-in-Charge, manufacture?s specification & drawing | 1 sqm | 1696 | |
647 | BMT-M.78 | Providing and fixing plain PVC rigid foam sheet wall panelling of thickness 5mm consisting of panels having size 1220mm X2440mm stuck on inner frame work of 25mm wide strips of 5mm thick PVC rigid foam sheet. The strips should have in their centre a grove of 6mm width and 2mm depth for sinking the head of the screw used to fix the strips to the wall and should be placed vertically at equal intervals of 405/407mm centre to c entre. The PVC strips shall be fixed to the wall using 65mm long M.S. screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 300mm. a groove of 2mm may be left at the joint of two panels for aesthetic looks. This framework is done for making existing wall surface in ensured level and for sticking the wall panelling sheet (panel) on it. The exact size of the panel and correspondingly of the grid May be varied depending n the size of the wall. However it must be ensured that a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement. , complete as per direction of Engineer-in-Charge, manufacture?s specification & drawing | 1 sqm | 1612 | |
648 | BMT-M.88 | Supply and fixing of wall panelling on the framework of wooded rippers of 24 X 24mm of required size. The entire framework shall be panelled with PVC section having overall dimensions of 6 X 250mm with a wall thickness of 1mm ± 0.3mm. The panels are joined with tongue and groove system. Necessary cut-outs for electrical connections to be provided at required places complete, for finished item of work. | 1 sqm | 1239 | |
Supply and fixing of wall lining fixing to GI channels of perimeter channel 30mm x 27mm x 0.55 thick and ceiling channels of 51.1mm x 26mm x 10.5mm x 0.55mm thick and fixing and finishing using joint compound and glass fibre tape complete finish as per specification without painting for finished item of work: | |||||
649 | BMT-M.47 | A) using 8mm thick Calcium silicate boards | 1 Sqm | 702 | |
650 | BMT-M.48 | B) Using 10mm thick Calcium silicate boards | 1 Sqm | 773 | |
651 | BMT-M.49 | C) Using 12mm thick Calcium silicate boards | 1 Sqm | 844 | |
652 | BMT-M.95 | Providing and fixing in position wall panelling to all heights with eco friendly light weight calcium silicate panels/tiles Globe Design of size 595mm x 595mm having square/butt edge having NRC(Noise Reduction Coefficient) of 0.5 to 0.75 as per IS 8225:1987, Light reflectance of 85%(minimum), Non Combustible as per BS:476 (part-4), fire performance as per BS:476 (part-6&7), humidity resistance of 100% and thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound & fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all complete.(With 15 mm thick integral densified fully perforated light weight calcium silicate panels/tiles) | 1 Sqm | 2155 | |
IV | PARTITIONS | ||||
653 | BMT-M.38 | Supply & fixing 75mm thick metal stud partition using 12.5 mm thick Gypboard conforming to IS 2095-1982 screw fixed to either side to 48 mm studs of 0.55 mm thick with the 50 mm floor and ceiling channel 0.55 mm and the joints duly finished with joint compound, paper tape and two coats Dry wall top coat as per specification. | 1 Sqm | 1044 | |
654 | BMT-M.44 | Supply and Fixing 66mm thick metal stud partition screw fixed to either side of 48mm studs of 0.55mm thick with 50mm floor and ceiling channel 0.55mm and the joints duly finished with joining compound, glass fibre tape and two coats dry wall top coat as per specification finished Item of work- using 8mm thick Calcium silicate boards | 1 Sqm | 1184 | |
655 | BMT-M.45 | Supply and Fixing 66mm thick metal stud partition screw fixed to either side of 48mm studs of 0.55mm thick with 50mm floor and ceiling channel 0.55mm and the joints duly finished with joining compound, glass fibre tape and two coats dry wall top coat as per specification finished Item of work - Using 10mm thick Calcium silicate boards | 1 Sqm | 1325 | |
656 | BMT-M.46 | Supply and Fixing 66mm thick metal stud partition screw fixed to either side of 48mm studs of 0.55mm thick with 50mm floor and ceiling channel 0.55mm and the joints duly finished with joining compound, glass fibre tape and two coats dry wall top coat as per specification finished Item of work - Using 12mm thick Calcium silicate boards | 1 Sqm | 1465 | |
657 | BMT-M.50 | Supply and Fixing 66mm thick metal stud partition using 2 layers of 12mm thick Calcium silicate boards screw fixed to either side to 48mm studs of 0.55mm thick with 50mm floor and ceiling channel 0.55mm.The boards joints are to be staggered to avoid through passage. Ceramic wool of 50mm thick, 64kg/m3 density is to be placed in cavity of the partition. The joints duly finished with joining compound, glass fibre tape and two coats dry wall top coat as per specification with out painting for finished item of work | 1 Sqm | 3745 | |
658 | BMT-M.67 | Supply and fixing double skin CEMENT BOARD partition with Frame work made of GI stud profile of size 48 x 40 x 10 x 0.6 mm thick placed at every 610 mm C/C intervals and 915 mm horizontal intervals duly fixed with self expansion screws, the E-board of 8 mm thick cladded around with self tapping self embedding screws fixed at every 300 mm (centres) leaving 3 mm gap between two panels of width 2?- 0” (610 mm). The gap will be covered with decorative moulding surface will be given a smooth finish over cement primer. The rate is inclusive of cost and conveyance of all materials and labour charges etc. complete. | 1 Sqm. |
1195 | |
659 | BMT-M.68 | Providing and fixing of 50mm thick SOLID WALL PANEL Sandwich panels made of light Weight FRACC two 4mm thick non-asbestos fibre reinforced cement sheets on either side of the lightweight concrete core composed of Portland cement binders with tongue and groove arrangement. The bottom of the panel shall be fixed to the floor channel made up of 1 mm thick GI channels of size 14x50x25 mm fixed to the existing floor with 6x60mm nylon self expansion screws at 600 mm C/C and top of the panel fixed with ceiling channel made out of 1mm thick GI Channel of size 38x50x38mm duly fixed to the existing ceiling with 6x60mm nylon self expansion screws at 600 mm C/C. All the tongue and groove joints of the panels have to be properly cleaned and both the panels have to be fixed by applying the mixture of fly ash and sodium silicate in between and Everest jointing compound all the exposed joints. The rate includes cost of 50mm SOLID WALL PANELS, G.l. Floor and ceiling channel. The panels can be flushed by using paper tape and Everest jointing compound all complete | 1 sqm | 1476 | |
660 | BMT-M.69 | Providing and fixing of 75mm thick SOLID WALL PANEL Sandwich panels made of light Weight FRACC two 4mm thick non-asbestos fibre reinforced cement sheets on either side of the lightweight concrete core composed of Portland cement binders with tongue and groove arrangement. The bottom of the panel shall be fixed to the floor channel made up of 1 mm thick GI channels of size 14x75x25 mm fixed to the existing floor with 6x60mm nylon self expansion screws at 600 mm C/C and top of the panel fixed with ceiling channel made out of 1mm thick GI Channel of size 38x75x38mm duly fixed to the existing ceiling with 6x60mm nylon self expansion screws at 600 mm C/C. All the tongue and groove joints of the panels have to be properly cleaned and both the panels have to be fixed by applying the mixture of fly ash and sodium silicate in between and Everest jointing compound all the exposed joints. The rate includes cost of 75mm SOLID WALL PANEL panels, G.l. Floor and ceiling channel. The panels can be flushed by using paper tape and Everest jointing compound all complete. |
1 sqm | 1762 | |
661 | BMT-M.72 | Supply and fixing CEMENT BONDED PARTICLE BOARDS (IS 14276) double skin partition using with 10 MM CEMENT BONDED PARTICLE BOARDS made out of G.I. track section of size 50mmx 35mm x 0.55 mm for fixing to the roof and floor and stud section of size 48mm x 35mm x 0.55mm placed in track section vertically at 610mm intervals and at 1200mm intervals horizontally fixed to the wall by means of self expansion screws and caps to the wall and roof. CEMENT BONDED PARTICLE BOARDS is to be fixed both sides of frame work by using self taping screws fixed at every 300mm intervals to the frame work leaving 3 mm gap between two panels. The cost inclusive with one coat of primer and two coats of smooth finish and cost and conveyance of all materials to site, labor charges etc., complete as per the direction of Engineer in charge. |
1 Sqm | 1696 | |
662 | BMT-M.73 | Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS double skin partition using with 10 mm CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS made out of G.I track section of size 50 mm x 35mm x 0.55mm for fixing to the roof and floor and stud section of size 48mm x 35mm x 0.55mm placed in track section vertically at 610mm intervals and at 1200mm internals horizontally. The frame is fixed by means of self expansion screws and caps to the wall / roof. LAM is to be fixed both sides of the frame work by using 2mm thick electro plated CR flat section leaving 3mm gap between two panels. The cost inclusive of cost and conveyance of all materials to sites, other materials incidentals and labour charges as per the direction of Engineer in charges. | 1 Sqm | 2336 | |
663 | BMT-M.75 | Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS aluminum glazed partitions using 10 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS and 5 mm thick plain glass to full height. Using with LAM to a height of 0.91 meter at bottom panel and remaining height with glass and aluminum sections anodized to 12 to 15 microns and of sections of size 37mm x 62mm and 1.5mm thickness with one meter centre to centre duly fixed with clip beading on both sides including fixing the frame to pillars by M.S. flats, bolts and nuts including cost and conveyance of all materials etc., complete as directed during execution. | 1 Sqm | 2908 | |
664 | BMT-M.76 | Providing and fixing 50mm thick SEMI HEIGHT SOLID PVC PARTITION consisting of 49mm sandwich PVC panel made out of 36mm high density expanded polystyrene sheet(E.P.S.-Thermocole) stuck on both side with 2mm thick plain/printed /prelam PVC rigid foam sheets reinforced with frame work made from 35mmX5mm M.S. Angle. In between two M.S. Angles 5mm thick plain/printed/prelam heat moulded PVC „C? channel of size 50X100mm with feathered edges shall be fixed on the floor & 50X75mm with feathered edges plain/printed /prelam PVC „C? channel. In between adjoining EPS sandwiched PVC partitions panel 5mm thickX75mm width plain/printed/prelam PVC sheet feathered at edges shall be stuck on front & back face using solvent cement etc. in places where two partitions meet to from an „L? shape the panels are joined 5mm thick plain/printed/prelam heat moulded “Rajshri” PVC „L? section of size 75mmX75mm with feathered edges shall be fixed on front & back side. This is done to maintain the symmetry of design. An additional 5mm thick PVC strip of 40mm width is to be stuck on the interior side of the „C? Channel using PVC solvent adhesive, complete as per direction of Engineer-in-Charge, manufacture?s specification & drawing | 1 Sqm | 2576 | |
665 | BMT-M.89 | Supply and fixing of PVC Double Skin Partition. The entire framework shall be carried out by mild steel section having overall dimensions of 24 X 48mm with a wall thickness of 1.2mm. The entire framework shall be concealed with PVC section having overall dimensions of 6 X 250mm with a wall thickness of 1mm ± 0.3mm both sides. Glass provision/Door provision can be provided along the partition wherever required. Partitions can be made full or half as per requirement complete, for finished item of work. | Sqm | 2175 | |
Supply and fixing of partitions made of seccolor pre-painted steel (base steel as per IS 513 of 0.58 mm thick „D? quality, galvanized as per IS 277 with Zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick alkyd backer. Section for outer frame should be 46x52mm, section for shutter should be 46x46mm, section for mullion should be 46x70mm, section for beading should be 18x25mm and section for middle and bottom rail (Lock Rail and Kick Rail) of size should be 23x130mm. The partition should be paneled with 9mm pre-laminated particle board to a height of 0.91m from the bottom, and remaining height with 5mm thick plain glass With Ethyl Propylene Diamine Monomer (EPDM) Gaskets. The sections are to be cut to length, mitre joined with corner bracket Centre mullions are to be fixed using mullion cap. Gaskets made of Ethyl Propylene Diamine Monomer (EPDM). Corner brackets made of CRCA with zinc phosphate. Mullion caps made of Glass filled nylon. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws, and complete for finished item of work. | |||||
666 | BMT-M.90 | Fixed Partition: Outer frame section size of 46x52mm, mullion section should be of 46x70mm, fixed beading should be of 18x25mm. | 1 sqm | 4477 | |
667 | BMT-M.91 | Fixed Partition with Door: Outer frame section size of 46x52mm, mullion section should be of 46x70mm, fixed beading should be of 18x25mm, section for shutter should be of 46x46mm and section for middle & bottom should be of size 23x130mm. |
1 sqm | 5105 | |
DRY WALL PARTITION WITH 50 MM THICK V-PANEL | |||||
668 | BMT-M.92 | CEMENT BONDED PARTICLE PLANK- 8 mm- size-150 mm X2440mm and 200mm X 2440mm | 1 Sqm | 613 | |
669 | BMT-M.93 | CEMENT BONDED PARTICLE PLANK- 10 mm- size-150 mm X2440mm and 200mm X 2440mm | 1 Sqm | 751 | |
670 | BMT-M.94 | CEMENT BONDED PARTICLE PLANK- 12 mm- Available size-150 mm X2440mm and 200mm X 2440mm | 1 Sqm | 919 | |
Note: Items BMT-M.33, BMT-M.34, and BMT-M.35 are removed in the section M and are brought as new items in the Section D as BMT-D.18, BMT-D.19 and BMT-D.20. | |||||
N. SECTION | DOORS (Landing cost – including loading, cost of conveyance, unloading) |
||||
I.SUB-SECTION | DOOR FRAMES | ||||
671 | BMT-N.80 | Powder Coated Mild Steel Hallow single rebate door frames manufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile size of 105 x 60 mm conforming to IS 4351 - 2003 including pretreatment, Galvanized as per IS:277, zinc phosphating finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 60 – 65 microns(Dry film thickness)Stainless Steel Ball Bearing Butt Hinges 3 mm thick fixed flush to the frame with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for both single and double shutter doors | 1 RM | 619 | |
672 | BMT-N.81 | Mild Steel Hallow single rebate general purpose door frames anufactured using cold roll formed process steel sheet of 1.25 mm thick bright (Cold Rolled Close Annealed (CRCA) and profile-B of size 105 x 60 mm conforming to IS 4351 - 2003 including pretreatment, phosphating with Hinges, Base Ties, Holdfast Lugs, Mortar Guards, shock absorbers and provision for Tower Bolts, Aldrops, Lock & Strike plates etc. for both single and double shutter doors | 1 Rm | 353 | |
673 | BMT-N.01 | Providing and fixing factory made polyvinyl chloride (PVC) Door Frame of the size 50 x 47mm with a wall thickness of 5mm, made out of extruded 10 mm rigid PVC foam sheet, mitre cut at two corners and joined with 2nos. of 150mm long brackets of 15x15mm M.S. square tube. The two vertical door profiles are to be reinforced with 19x19mm M.S. Square tube of 19 gauge. The door frame shall be fixed to the wall using 65/100mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4nos. of screws to be provided for each vertical member & minimum 2nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in- Charge for finished item of work | 1 Rm | 330 | |
674 | BMT-N.05 | SINGLE SIDE PRELAM SOLID PANEL PVC DOOR FRAME (CHOUKHAT): Providing and fixing factory made Pac single side Prelam door frame of the size 50X47 mm with a wall thickness of 5mm, made out of extruded 5mm rigid Pac single side prelam sheet, meter cut at two corners and joined with 2nos. of 150mm long brackets of 1515mm MS.Square tube. The two vertical door profiles are to be reinforced with 19X19mm MS. square tube of 19guage. The door frame shall be fixed to the wall using 65/100mm long MS. Screws through the frame by using Pac fasteners. a minimum of 4nos. of screws to be provided for each vertical member and minimum 2nos. for horizontal member etc. complete as per manufacture specification and direction of Engineer-in-charge. | 1 Rm | 330 | |
675 | BMT-N.32 | Supply and fixing of door frame made of hollow extruded PVC section having dimensions of 40 X 57mm with the wall thickness of 2mm +/- 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2 corners shall be metri-cut/ welded. PVC DOOR FRAME | 1 RM | 237 | |
676 | BMT-N.33 | Supply and fixing of door frame made of hollow extruded PVC section having dimensions of 40 X 46 mm with the wall thickness of 2mm +/- 0.2mm duly reinforced with seasoned wood plank at the hinges side. The door frame top 2 corners shall be mitre cut/welded | 1 RM | 186 | |
677 | BMT-N.34 | Supply & fixing of Door frames made of all formed sections of 1.25mm thick CRCA section, size should be 50x60mm with 32mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. complete for finished item.: Single shutter 3'-0" x 7'-0" (914.4x2133.6mm) outer frame section size of 50 x 60 mm | 1RM | 197 | |
678 | BMT-N.35 | Supply & fixing of Door frames made of all formed sections of 1.25mm thick CRCA section, size should be 50x60mm with 32mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. complete for finished item.: Double shutter 5'-0" x 7'-0" (1524 x 2133.6mm) outer frame section size of 50 x 60 mm | 1 RM | 200 | |
679 | BMT-N.36 | Supplying & fixing of Door frame made of roll formed section of 1.25 mm thick CRCA section, size should be 50 x 60 mm with 32 mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. Complete for finished item of work.: Single shutter 3'- 0" x 7'-0" (914.4x2133.6mm) outer frame section size of 50 x 75 mm | 1 RM | 225 | |
680 | BMT-N.37 | Supplying & fixing of Door frame made of roll formed section of 1.25 mm thick CRCA section, size should be 50 x 60 mm with 32 mm rebate. The corner of the frame should be welded. The frame should be painted with one coat of primer and finished painted with pure polyester paint. The frame should be provided with approved quality butt hinges of 3 Nos. Complete for finished item of work.: Single shutter 5'- 0" x 7'-0" (1524x2133.6mm) outer frame section size of 50 x 75 mm | 1 RM | 231 | |
681 | BMT-N.38 | Providing and fixing door frames fabricated from sections made of galvanized steel powder coated (base steel as per IS 513, galvanised as per IS 277 with zinc of 120 grams / square metre), the factory made section are powder coated with pure polyester powder of 50-60 microns thick with total coated thickness of 1.25 mm, size of door frame section is of 105 x 60 mm with a rebate of 38 mm to accommodate 35 mm thick door shutter, with groove to insert gasket in the frame section, frame section filled with polyurethane foam, cut to length, and joined by way of welding, each frame provided with: a) 2mm thick MS powder coated butt hinges of 100 mm long – 3 Nos. for single shutter, 6 Nos. for double shutter. b) CRCA electroplates stiffeners of 6 Nos. – 3 in each vertical. c) 40 mm x 200 mm x 1.2 mm hold fasts screwed to stiffeners – 6 Nos. with split end tail. d) Nylon Aldrop Receiver – 1 No. for single shutter frame. e)Tie Rod – 1 No |
1 RM | 690 | |
682 | BMT-N.39 | Providing and fixing of door frames factory made, internal door frames without threshold, fabricated from pre painted cold roll formed section 100 mm x 60 mm made of galvanized (base steel as per IS-513 „D? quality galvanized as per IS-277 with Zinc of 120 Gms/sqm) steel colour coated sections with total coated thickness of 1 mm primer coated with epoxy primer of 5-7 microns thick finish painted with polyester paint of 12-16 microns and back coated with alkyd backer of 5-7 microns, the frame section filled with polyurethane (PU Foam) of 40 kg/Cu.m and the sections cut to length and mitre joined by means of 1.25 mm thick CRCA electroplated corner brackets of size 75 x 75 mm and 1.25 mm thick electroplated stiffeners of size 150 mm for fixing hold fasts and hinges with MS Powder coated fittings a) 6 Nos M.S. Z Type hold fasts made of 30 mm x 3 mm MS flat of 230 mm long, 3 Nos each size expandable PVC covered screw type fasteners b) 2.5 mm x 300 mm long „T? hinges /2.5 mm x 50 mm x 50 mm x 100 mm two way but hinges (3 Nos for single leaf or 2 Nos for Double leaf/leaf) c) 12 mm dia MS tie rod at bottom with necessary size of nuts on either side. | 1 RM | 410 | |
683 | BMT-N.54 | Providing & fixing internal prelaminated PVC door frame of size 100 x 45 mm with a wall thickness of 5mm, made of extruded 5 mm Prelam PVC foam sheet, mitred cut at two corners and joined with two nos. of 150mm long brackets of 15 x 15 mm MS square tube, two vertical door profiles reinforced with 40 x 20 MS Tube of 19 guage throughout the frame and the door frame fixed to the wall using 65/100mm long MS screws through the frame by using PVC fasteners with a minimum of 3 nos of screws provided for each vertical member and two nos. for horizontal, etc complete as per drawing and direction of Engineer in Charge | 1 RM | 550 | |
684 | BMT-N.72 | PVC Door frame made out of PVC material conforming to IS:10151:1982. The door frame shall be made from extruded PVC Section in overall dimensions of 40mm x 48mm having wall thickness of 1.1mm +/-0.3mm with usual process variation corresponding to Sintex code number RUPS 414. The frame shall be Reinforced with special polymeric reinforcement as shown in drawing to take up necessary hardware. The corner joint shall be mitre cut and welded or joined by means of concealed cleats with necessary screws fittings. A tie rod to be provided at bottom. [Laminated Profile] | Per Rmt. | 196 | |
685 | BMT-N.83 | Providing and fixing factory made solid Wood Polymer Composite (WPC) single extruded Door Frame section of size with encapsulation of 8MM rigid layer on all the six surfaces. The door frame will have a rebat of 32MM. | |||
686 | BMT-N.83.A | Door Frame section of 45x75 MM . The two Vertical members are to be joined together with the horizontal member using 8x50 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. | 1 Rm | 506 | |
687 | BMT-N.83.B | Door Frame section of 45x90 MM . The two Vertical members are to be joined together with the horizontal member using 8x60 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. | 1 Rm | 645 | |
688 | BMT-N.83.C | Door Frame section of 63.5x100 MM .The two Vertical members are to be joined together with the horizontal member using 8x75 MM long MS Star full thread screws to be used with reverse forward speed control hand drilling machine. The ready/assembled door frame is fixed to the wall using hold fast or bolt fasteners. A minimum of 4 No.s of screws to be provided for each vertical member & minimum 2no.s for horizontal member. | 1 Rm | 805 | |
689 | BMT-N.82 | Supply and fixing of factory made Bathroom door frames without threshold, fabricated from pre-painted cold roll formed section 50mm x 50 mm made of galvanized (base steel as per IS – 513 „D? quality, galvanized as per IS-277 with Zinc of 120 Gms/sqm) steel colour coated sections with total coated thickness of 1 mm, primer coated with epoxy primer of 5-7 microns thick, finish painted with polyester paint of 12-16 microns and back coated with alkyd backer of 5-7 microns and the frame section filled with polyurethane (P.U. Foam) of 40 Kg/Cum; and the sections cut to length and mitre joined by means of 1.25mm thick CRCA electroplated corner brackets of size 75 x 75 mm and 1.25mm thick electroplated stiffeners of size 150mm for fixing hold fasts and hinges together with the following MS Power coated fitting (Supply and fixing) of approved make. (a) 6 Nos M.S. Z. Type hold fasts made of 30mm x 3 mm MS flat of 230mm long, 3 Nos each side expandable PVC covered screw type fasteners. (b) 2.5 mm x 300 mm long „T? hinges / 2.5mm x 50 mm x 100mm two way but hinges (3 Nos for single leaf or 2 Nos for Double leaf /leaf ) (c) 12 mm Dia MS tie rod at bottom with necessary size of nuts on either side. |
1 RM | 407 | |
II.SUB- SECTION | DOOR SHUTTERS WITHOUT FRAMES | ||||
690 | BMT-N.12 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 25 mmthick conforming to IS:2202 | 1 sqm | 1790 | |
691 | BMT-N.13 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 30 mmthick conforming to IS:2202 | 1 sqm | 1860 | |
692 | BMT-N.14 | Flush door shutters, solid bond wood block board type with teak ply on both faces.: 35 mmthick conforming to IS:2202 | 1 sqm | 2031 | |
693 | BMT-N.15 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 25 mmthick conforming to IS:2202 | 1 sqm | 1041 | |
694 | BMT-N.16 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 30 mmthick conforming to IS:2202 | 1 sqm | 1232 | |
695 | BMT-N.17 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 35 mmthick conforming to IS:2202 | 1 sqm | 1396 | |
696 | BMT-N.18 | Flush door shutters, solid bond wood block board type with commercial ply on both faces.: 40 mmthick conforming to IS:2202 | 1 sqm | 1564 | |
697 | BMT-N.19 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 20 mmthick conforming to IS:2202 | 1 sqm | 1960 | |
698 | BMT-N.20 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 25 mmthick conforming to IS:2202 | 1 sqm | 1893 | |
699 | BMT-N.21 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 30 mmthick conforming to IS:2202 | 1 sqm | 2096 | |
700 | BMT-N.22 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 35 mmthick conforming to IS:2202 | 1 sqm | 2285 | |
701 | BMT-N.23 | Flush door shutters, solid bond wood block board type with teak veneer on one face and commercial ply on another face (lipping): 40 mmthick conforming to IS:2202 | 1 sqm | 2612 | |
702 | BMT-N.25 | Supply and fixing Cement Bonded Particle Board (IS 14276) single door shutter using with 16MM Cement Bonded Particle Board with all-round "U" section of size 12mmx18mmx12mm made from 0.6 mm thick galvanized, color quoted cold rolled steel profiles with necessary screws fixed at every 304.8 mm intervals. The cost inclusive of MS Nickel coated Aldrops of size 255 mm long 2 Nos., 200 mm long tower bolts 1 No., 125 mm handles 2 Nos. 300 mm long "T" hinge cost and conveyance of all materials at site and applying 1 coat primer, 1 coat of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work. |
1 Sqm | 1889 | |
703 | BMT-N.26 | Supply and fixing of Cement Bonded Particle Board(IS 14276) door shutters using with 16MM Cement Bonded Particle Board with all round style “U” size of 20mmx18mm x20mm made from 0.6mm thick galvanized pre-painted cold rolled steel profiles with Cement Bonded Particle Board separating two shutter with 30mmx18mmx30mm Stepped lipping with necessary screws fixed at every 1?-0” (304.8mm) intervals. Ms Nickel coated 250 mm long aldrops 2 no?s, MS powder coated 250mm long tower bolt 2no?s , & 2no?s MS powder coated 125 mm long grip handle. Including cost and conveyance of all materials at site and applying one coat of primer, 2 coats of lappum and 2 coats of synthetic enamel paint as per approved design for finished item of work. |
1 Sqm | 2654 | |
704 | BMT-N.79 | Supply and fixing of CEMENT BONDED PARTICLE BOARD double door shutter using 16 MM CEMENT BONDED PARTICLE BOARD LAM with all round “U” section size of 20mm x 18mm x20mm made from 0.6mm thick galvanized pre-painted cold ro steel profiles with CEMENT BONDED PARTICLE BOARD LAM separating two shutter with 30mm x lled 20mm x 30mm stepped lipping with necessary screws fixed at every 1?0” (304.8mm) intervals. The cost inclusive of MS Nickel coated 250mm long aldrops 2no?s, MS powder coated 125mm long grip handle, 2 no?s M.S.P.C. Door stopper. Including cost and conveyance of all materials at site labor charges etc., complete finished item of work. | 1 Sqm | 2687 | |
705 | BMT-N.30 | Supply and fixing of CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS door shutter made out of U sections of size 12x14x12 made from 0.6mm thick pps sections with 12MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS with necessary screws fixed at every 1?.0”interwells. The hardware consists of 250mm long aldrop – 2 Nos.150mm Handle- 1 No , 150 mm long ms powder coated tower bolt 1 no. nickle coated. The cost is inclusive of all incidentals, labor transportation charges. | 1 Sqm | 2205 | |
706 | BMT-N.63 | Supply and fixing of BOARD (conforming toIS 14862) door shutter with all-round style “U” lipping size 15 x 18 x 15 mm made from 0.8 mm thick powder coated cold rolled steel profiles with 16 mm thick V-BOARD with necessary screws fixed at 1?-0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance of all materials at site and applying 1 coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work. | 1 Sqm | 1350 | |
707 | BMT-N.27 | Supply and fixing of Cement Bonded Particle Board (IS 14276) LAM double door shutter using 16 MM CEMENT BONDED PRE-LAMINATED PARTICLE BOARDS with all round “U” section size of 20mm x 18mm x 20mm made from 0.6mm thick galvanized pre-painted cold rolled steel profiles with Cement Bonded Particle Board (IS 14276) LAM separating two shutter with 30mm x 20mm x 30mm stepped lipping with necessary screws fixed at every 1?0” (304.8mm) intervals. The cost inclusive of MS Nickel coated 250mm long aldrops 2no?s, MS powder coated 125mm long grip handle, 2 no?s M.S.P.C. Door stopper. Including cost and conveyance of all materials at site labour charges etc., complete finished item of work. |
1 Sqm | 2222 | |
708 | BMT-N.47 | Moulded panel solid core flush doors using water-resistant hardwood fibre HDF / MDF fibre boards skins of 2.5 mm thick doors - 30 mm thick | 1 Sqm | 1637 | |
709 | BMT-N.48 | Moulded panel solid core flush doors using water-resistant hardwood fibre HDF / MDF fibre boards skins of 2.5 mm thick doors - 35 mm thick | 1 Sqm | 1810 | |
710 | BMT-N.49 | Solid core membrane flush doors using rigid PVC membrane of 0.3 mm thick of different elegant shades doors - 30 mm thick | 1 Sqm | 1350 | |
711 | BMT-N.50 | Solid core membrane flush doors using rigid PVC membrane of 0.3 mm thick of different elegant shades doors - 35 mm thick | 1 Sqm | 1502 | |
712 | BMT-N.06 | Providing and fixing 35mm thick BRAND FACTORY MADE MOULDED DOOR SHUTTER consisting of sold core single leaf flush door of 30mm thickness, lipped with 15mm (5mmX3) thick X 30mm width on one stiles and top rails and 10mm (5mmX2) thick X 30mm width on the other stiles and bottom rails. The inner panel laminated with 2mm thick termite proof, water proof and fire resistant moulded Pac sheet with 2,4,6 raised panel design in different panel and / or prelam colours on one side after routing the moulded design on flush door and 2mm prelam Pac sheet on other side using rubber adhesive on flush door and solvent cement adhesive on Pac lipping etc. complete as per direction of Engineer-in-Charge, manufacture specification and drawing | 1 sqm | 2726 | |
713 | BMT-N.31 | Supply and fixing of door shutters made of rigid PVC extruded hollow section of 20mm X 200 mm with the wall thickness of 1.0mm +/- 0.1mm equally divided into 4 no's with tongue and groove locking arrangements. The shutter frame is made of 30mm X 79mm with the wall thickness of 1.5mm +/-0.15mm section mitre-cut and joined at 4 corners with 125mm X 225mm plastic brackets. The shutter shall be horizontally reinforced with 2 no's of 8mm PVC rods. Teak wood batons shall be reinforced inside the door shutter during the fabrication of the door shutter at those points wherever the hardware is fixed onto the door shutter. | Sqm. | 1690 | |
714 | BMT-N.52 | Supply & Fixing SOLID STEEL DOOR door shutter made out of G I Precoated Sheet with an average wall thickness of 0.35 mm on both sides. MS Tube having dimensions of 19 x 19 mm is inserted along the hinge side of the door, core of the door shutter filled with High Density Polyurethane foam injected with the help of hydraulic injection method, four sides of the door covered with G I Precoated Sheet and the hardware locations reinforced with suitable wooden blocks as per drawing and stickers indicating location of the hardware pasted at appropriate places, etc complete | 1 Sqm | 1400 | |
715 | BMT-N.64 | Supply and fixing of BOARD (conforming toIS 14862) 12 mm thick door shutter of size 6’0” x 2’6” withall-round style “U” lipping size 15 x 14 x 15 mm made from 0.8 mm thick powder coated cold rolled steel profiles with necessary screws fixed at 1?-0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance of all materials at site and applying 1 coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved design for finished item of work. | 1 Sqm | 1160 | |
716 | BMT-N.68 | Providing of 35mm thick Facotry made Prelaminated ABS (Acrolynitrile Butadyne Styrene) Door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32x 32mm - 2 nos. for vertical made out of LVL (Laminated Veneer Lumber), core material of 32 mm thick high density craft paper honey comb board, sandwiched on both sides with prelaminated ABS sheet thickness of 1.5mm . PVC edge banding of size 0.45mm on the vertical sides.for each shutter and ISI make S.S round lock complete for finished item of work | 1 Sqm | 6200 | |
III.SUB- SECTION | DOORS WITH SHUTTERS & FRAMES | ||||
717 | BMT-N.02 | Providing and fixing 30mm thick Solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat moulded PVC „C? channel of size 30 x 50mm forming stiles, and 5mm thick, 75mm wide PVC sheets for top rail, lock rail &bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the „C? Channel using PVC solvent adhesive. Complete as per direction of Engineer-in-charge, manufacturer?s specification & drawing for finished item of work . | 1 Sqm | 2270 | |
718 | BMT-N.03 | Providing and fixing 30mm thick BRAND FACTORY MADE BOTHSIDE PRELAM SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of MS. Tubes of 19gauge thickness and size of 19mmX19mm for stiles, top and bottom rails. MS. Frame shall have a coat of steel primers of approved make and manufacture. MS. Frame covered with 5mm thick heat moulded Prelam Pac „C? channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 450 angle on either side forming stiles; and 5mm thick, 95mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered in 450 on the inner side to form top and bottom rail 115mm wide Prelam Pac sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rail shall be provided either side of the panel. 10mm (5mmX2) thick, 20mmwide cross Pac sheet shall be provided as gap insert for top and bottom rail. Panelling of 5mm thick both side Prelam Pac sheet to be fitted in the MS. Frame welded/ sealed to the stiles & rails with 7mm(5mm+2mm) thick X 15mm wide Pac sheet beading on inner side, and joined together with solvent cement adhesive etc. an additional 5mm thick Pac strip of 20mm width is to be stuck on the interior side of the „C? channel using Pac solvent cement adhesive etc. complete as per direction of Engineer – in-charge, manufacture specification and drawing. | 1 Sqm | 2515 | |
719 | BMT-N.04 | Providing and fixing 30mm thick BRAND FACTORY MADE SOLID SINGLE SIDE PRELAM PANEL PVC DOOR SHUTTER consisting of frame made out of MS. Tubes of 19gauge thickness and size of 19mmX19mm for stiles, and 15mmX15mm for top and bottom rails. The MS. Frame shall have a coat of steel primers of approved make and manufacture. MS. Frame covered with 5mm thick heat moulded single side Prelam Pac „C? channel of size 30mmX50mm to form stiles.5mm thick& 75mm wide single side prelim Pac sheets shall be for the top, bottom and lock rails. Panelling of 5mm thick one side Pac sheet to be fitted in the MS. Frame and sealed to the front (prelam side) stiles and rails (which should have a 5mm 45 bent portion as beading) and attached to the back(white/ivory) stiles and rails which should have a 10mm 900 bent portion as beading ) using 2nos. 15mm wide X 5mm thick Pac sheet beading inside the 90 bent beading. All stiles, rails and beadings are to be joined to the panel using solvent cement etc. an additional 5mm thick Pac strip of 20mm width to be stuck on the interior side of the „C” channel using Pac solvent cement adhesive and 10mm(5mmX2) thick, 20mm wide cross Pac sheet to be fitted as gap insert for top and bottom rail etc. complete as per direction of Engineer –in-Charge, manufacture specification and drawing. | 1 Sqm | 2198 | |
720 | BMT-N.07 | MOULDED PVC DOOR - WOOD FREE Providing and fixing 30mm thick Brand factory made Moulded door shutter- wood free consisting of frame made out of MS. tubes 19gauge thickness and size of 25mmX25mm for stiles, top and bottom rails. MS. Frame shall have a coat of steel primers. The inner panel shall consist of 25mm thick High density EPS conforming to IS 4671-1984 bounded with 2mm thick termite proof, water proof and fire resistant moulded Pac sheet with 2,4,6 raised panel design in different plain and / or prelam colours after routing to the moulded design on one side and 2mm plain and / or prelam Pac sheet on other side of the EPS. The edge of panel to be sealed with lipping of 10mm wide PVC sheet bottom (made by sticking 2 rigid foam sheet of 5mm thickness using Pac solvent cement) and stiles sides 25mm(5mmX5) thick and 30mm width Pac sheet fitted along Ms. Tube for lock provision for lock height 5mm thick Pac sheet of size 150mmX100mm fixed with upper and lower face of inner side of EPS Panel etc. Complete as per direction of Engineer – in-Charge, manufacture specification and drawing | 1 Sqm | 2265 | |
721 | BMT-N.08 | Providing and fixing 30mm thick BRAND FACTORY MADE WIRE MESH SOLID PVC DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mmX19mm for stiles and 15mm for top, lock & bottom rails. MS. Frame shall have a coat of steel primers of approved make and manufacture. 19mmX19mm M.S. square tubes shall be covered with 5mm thick heat moulded PVC „C? channel of size 30mm thickness, 90mm width out of which 75mm shall be flat and 15mm shall be flat and 15mm shall be bent in 900 on the inner side to from top and bottom rail land 130mm wide PVC sheet out of which 100mm shall be flat and 154mm shall be bent in 900 on both side to from lock rail, 10mm(5mmX2) thick, 20mm wide cross PVC sheet as gap insert for top rail & bottom rail. Panel will be of G.I.wire mesh of 24gauge to be fitted in by ?C? channel of size 35mm X10mm on the either side in the stiles. The inner side „C? channel is fixed by 19mmX19mm MS. Tube on both sides with screws. The wire mesh in top bottom & lock rail is sealed with15mm X 15mm tube with G.I.wire 10mm(5mmX2) thick PVC strip of 25mm width is to be stuck& nails on both side of G.I. wire mesh interior at the top, bottom & lock rail. An additional 5mm thick PVC srip of 20mm width is to be stuck on the interior side of the „C? channel using PVC solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer?s specification & drawings | 1 Sqm | 2000 | |
722 | BMT-N.65 | Providing and fixing frame made from 1.2 mm powder coated cold rolled steel profiles of overall section size of 60 mm x 45 mm with 21 mm rivet for shutter with necessary stiffeners hinges and screws. BOARD (IS 14862) shutter with all-round style “U” lipping of size 15 x 18 x 15 mm made from 0.8 mm thick CRCA powder coated steel profile with 16 mm thick V-board with necessary screws fixed at every 1?-0” interval 250 mm long aldrops 2 nos. M.S. nickel coated 250 mm long 1 no. M.S. Tower Bolts Including cost and conveyance. One coat of primer, 2 coats of luppum and 2 coats of synthetic enamel paint as per approved colour, labour charges etc. | 1 Sqm | 1600 | |
723 | BMT-N.28 | Providing and fixing of door frame made from cold roll formed sections made of galvanized (Base steel as per IS277 with zinc of 120 Gms/sqm) colour coated steel sections with total coated thickness of 1mm, primer coated with epoxy primer coat of 5-7 microns thick, finish paint with polyester paint of 12-16 microns. The Section for door frame is to be filled with polyurethane (P.U) form of 40kg/m3. Overall size of frame section should be of 50mm x 50mm. With necessary corner brackets, stiffeners, hinges, and screws. Cement Bonded particle board shutter “Single Leaf” with all round styles “U” section of size 12m x 18m x 12mm made from 0.6 mm thick galvanized, colour coated cold rolled steel profiles with 16mm thick Cement Bonded particle Board with necessary screws fixed at every 1?-0” (304.8mm) intervals. The cost inclusive of MS nickel coated Aldrop of size 250mm long 2nos. 200mm long tower bolt 1no., 125mm handles 2nos., cost and conveyance of all materials at site and applying one coat primer , one coat of luppum and two coats of synthetic enamel paint as per approved design for finished item of work | 1 Sqm | 3488 | |
_ | _ | DOORS FRAMES (COLOUR COATED STEEL SECTIONS) & SHUTTER USING CEMENT BONDED PARTICLE BOARD AS PER IS 14276: | _ | _ | |
724 to 727 | BMT-N.40 to BMT-N.43 | ITEM DELETED | |||
728 | BMT-N.44 | Supplying and fixing door shutter, with shutter frame and infill panel made from PVC material conforming to IS: 10151-1982, the shutter frame made out of PVC extruded sections having overall dimension of 47 mm x 33 mm with wall thickness of 1.2mm + 0.3mm with usual process variation, the shutter frame with tapered shape to provide better grip to the infill panel end to drain out the water The Infill panel is made out of PVC Sections having Overall Dimensions of 200 mm x 20 mm with wall thickness of 1mm + 0.2mm, the shutter frames mitre cut and joined at the corner, by providing Polymeric “ L” type corners to take hardware & fixtures fixed with 10-20mm counter sunk fully threaded parallel shank steel screws, all the hardware locations reinforced with special polymeric bars as per drawings, stickers showing locations of different hardware pasted on the shutter, the infill panels joined by tongue and groove method. | 1 Sqm | 910 | |
729 | BMT-N.45 | Providing & Fixing of Scientific Doors with metal door frames and door shutters made of galvanize steel (base steel as per IS 513 of 0.58 mm thick D quality, galvanized as per IS 277 with Zinc of 120 GSM)coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 50-60 microns (Dry film thickness) outer frame section of 100 x 58 mm x 1.2 mm thick, shutter section of 0.80 mm thick galvanized steel sheet pressed (roll formed) for 46mm thick fully flush, double skin door shell seam joints at stile edges, in-fill of honeycomb kraft paper used to give the required rigidity and effective acoustic insulation with 6” Tower bolt – 1 No., 6” D handles – 2 Nos., 10” Aldrop – 1 No., Butt Hinges – 3 Nos, Mortise Lock of approved quality – 1 No, frames fixed to the concrete/masonry wall by means of self expanding screws complete for finished item of work for Single leaf Door | 1 Sqm | 9348 | |
730 | BMT-N.46 | Providing & Fixing of Scientific Doors with metal door frames and door shutters made of galvanize steel (base steel as per IS 513 of 0.58 mm thick D quality, galvanized as per IS 277 with Zinc of 120 GSM). coated with Zinc Phosphate Primer to receive any paint on site or finished with Thermosetting Polyurethane paint of Aliphatic Grade providing high levels of scratch resistance and durability/Epoxy polyester powder for powder coating paint thickness 50-60 microns (Dry film thickness) outer frame section of 100 x 58 mm x 1.2 mm thick, shutter section of 0.80 mm thick galvanized steel sheet pressed (roll formed) for 46mm thick fully flush, double skin door shell seam joints at stile edges, in-fill of honeycomb kraft paper used to give the required rigidity and effective acoustic insulation with 6” Tower bolt – 2 Nos., 6” D handles – 2 Nos., 10” Aldrop – 1 No., Butt Hinges – 6 Nos, Mortise Lock of approved quality – 1 No, frames fixed to the concrete /masonry wall by means of self expanding screws complete for finished item of work for Double leaf Door | 1 Sqm | 9971 | |
731 | BMT-N.51 | Providing & fixing 30 mm thick solid panel PVC door shutter consisting of frame made out of 19 guage M.S tube of 19 x 19 mm for stiles, top & bottom rail, with a coat of primer of approved make. M.S. Frame covered with 5 mm thick heat moulded PVC “C” channel of size of 30 x 50 mm forming stiles, 5 mm thick 75 mm wide PVC sheet for top, lock & bottom rail on either side 20 mm wide cross PVC sheet as gap insert for top & |