GATE MFG AND REPAIRS



GOVERNMENT OF MAHARASHTRA
COMMON SCHEDULE OF RATES FOR 2017-18
GATE MANUFACTURING AND REPAIRS
 

Sl. No. Item Unit Rate for 2017-18 (Rate in Rs.)
Completed Item Labour
  RADIAL GATE EMBEDMENT - Manufacturing, Erection, Commissioning & Testing      
191 Item No.191 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of embedded parts of Radial gate with parts consisting of Erection Jig, Vertical Anchorages, Trunion Chair, Trunion Girder box / Yoke Girders, Horizontal anchorages, Trunion bracket assly, Wall plate assly, Sill beam assly, trunion supports, Locking arrangement, etc. All material used shall conformed to related IS Codes specified in IS 4623. Above item covers Mild steel confirming to IS 2062. The tolerances between Components & assembly Shall confirm to IS 4623.the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit) & with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference ) as per IS 4623. Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Zinc (IS 209), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177,The embedment & gate assembly shall be reasonably water tight, the maximum permissible leakage being not more than 5 liters/min/m wetted length of seal. The surface finish of seal plates should be within the range of 1.6 to 6.3 μm (IS 9349).
MT 109647.00 21415.00
  RADIAL GATE LEAF - Manufacturing, Erection, Commissioning & Testing      
192 Item No.192 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Gate leaf of Radial gate with parts consisting of End arm assly, Horizontal Girder, Skin plate assly, tie flats / Channels, Bracing Angles & Gusset plate etc. All material used shall conformed to related IS Codes specified in IS 4623. Above item covers Mild steel confirming to IS 2062. The tolerances between Components & assembly Shall confirm to IS 4623. The fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit )& with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference ) as per IS 4623. Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Zinc (IS 209), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177, The embedment & gate assembly shall be reasonably water tight, the maximum permissible leakage being not more than 5 liters/min/m wetted length of seal. The surface finish of seal plates should be within the range of 1.6 to 6.3 μm (IS 9349).
MT 105128.00 20159.00
  HOIST BRIDGE - Manufacturing, Erection, Commissioning & Testing      
193 Item No.193 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Hoist Bridge. All materials used shall confirmed to related IS Codes. Mild steel used for manufacturing shall conform to IS 2062. Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 89069.00 24575.00
  ROPE DRUM HOIST without Hoist Bridge - Manufacturing, Erection, Commissioning & Testing      
194 Item No.194 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing with 125 % of rated capacity of Rope Drum Hoist consisting of central drive unit, gear train frames, rope drums, gears, pinions, shafts, 3 phase electric motor, brake, reduction gear box, wire ropes, gate position indicators, manual operation arrangement, ICTP main switch, electric starter, etc. All material used shall conformed to related IS Codes specified in IS 6938. Above item covers Mild steel confirming to IS 2062. the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit )& with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference ) as per IS 4623. Other Material includes C.I (IS 210), C.S (IS1030), P. Bronze (IS 305), Al. Bronze (IS 318), S.S (IS 6911), Wire rope (IS 2266), Wire rope sockets ( Is 2485), 3p S4 duty Induction Motor (IS 325), Reduction gear box ( IS 7443), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, (Item contd. on next page) machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total sloventless coal tar epoxy paint applied to give dry film thickness 70 +/- 5 microns and 2 coats of minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 171888.00 16413.00
  VERTICAL LIFT BARRAGE GATE EMBEDMENT / STOP LOG GATE EMBEDMENT -
Manufacturing, Erection, Commissioning & Testing
     
195 Item No.195 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of embedded parts of V.L. Barrage gate/Stop log gate Consisting of Primary Embedments, Sill beam, Roller Track, Side guide, Side seal kit etc. All material used shall conformed to related IS Codes. Mild steel confirming to IS 2062.The tolerances between Bushing / Bearing /Pin Should confirm to IS 919 (Part I & II). Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.The embedment & gate assembly shall be reasonably water tight, the maximum permissible leakage being not more than 5 liters/min/m wetted length of seal. The surface finish of seal plates should be within the range of 1.6 to 6.3 μm (IS 9349).
MT 112050.00 18708.00
  VERTICAL LIFT BARRAGE GATE LEAF / STOP LOG GATE LEAF -
Manufacturing, Erection, Commissioning & Testing
     
196 Item No.196 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Gate leaf of V.L. Barrage gate Consisting of following parts. Gate Leaf, Horizontal girder, Guide roller assembly, & Roller Assembly. All material used shall conformed to related IS Codes. Mild steel confirming to IS 2062.The tolerances between Components & assembly Shall confirm to IS 4623.the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit) & with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference) as per IS 4623. Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177,The embedment & gate assembly shall be reasonably water tight, the maximum permissible leakage being not more than 5 liters/min/m length of seal.
MT 103974.00 21150.00
  PYLON STRUCTURE - Manufacturing, Erection, Commissioning & Testing      
197 Item No.197 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Pylon Structure. All materials used shall confirmed to related IS Codes. Mild steel used for manufacturing shall conform to IS 2062. Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead
(Item contd. on next page) charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 141
MT 89939.00 18233.00
  GOLIATH CRANE - Manufacturing, Erection, Commissioning & Testing      
198 Item No.198 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing with 125 % of rated capacity of Goliath Crane consisting of drive unit, A Frame, Main Frame, , LT Driving and driven trolleys, CT Crab Including Central Drive unit, gear train frames, rope drums, gears, pinions, shafts, Driving electric motor, brake, reduction gear box, wire ropes, manual operation arrangement, ICTP main switch, electric starter, etc. All material used shall conformed to related IS Codes specified in IS 6938. Above item covers Mild steel confirming to IS 2062. the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit )& with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference ) as per IS 4623. Other Material includes C.I (IS 210), C.S (IS1030), P. Bronze (IS 305), Al. Bronze (IS 318), S.S (IS 6911), Wire rope (IS 2266), Wire rope sockets ( Is 2485), 3p S4 duty Induction Motor (IS 325), Reduction gear box ( IS 7443), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints ). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 128299.00 15406.00
  GOLIATH RAIL ARRANGEMENT - Manufacturing, Erection, Commissioning & Testing      
199 Item No.199 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Railing arrangement for Goliath Crane (Span 27 mtr).MS Material used shall conform to IS 2062. The Dimensions, shape and other requirements of Crane rail sections conform to IS 3443.Welding electrodes (AWS E6013 for MS to MS weld joints & E7016 for MS to rail weld joints). It includes all materials, Labour charges, machining and machinery charges, 1 km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns as per IS 14177.
MT 83707.00 9783.00
  LIFTING BEAM - Manufacturing, Erection, Commissioning & Testing      
200 Item No.200 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Lifting Beam.MS Material used shall conform to IS 2062. All parts of Lifting Beam like Guide rollers, Hooks, Pins, conform to IS 13591.Welding electrodes (AWS E6013 for MS to MS weld joints & E7016 for MS to rail weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 74766.00 12854.00
  OUTLET GATE-SLIDING TYPE EMBEDMENT - Manufacturing, Erection, Commissioning & Testing      
201 Item No.201 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Sliding type gate Embedments consisting of following parts. Sill Beam, Track Girder, Vertical Seal & Horizontal Seal assly. Guide Tee & Lining Plate. Anchorages etc. All material used shall conformed to related IS Codes. All material used shall conformed to related IS Codes specified in IS 9349. Mild steel confirming to IS 2062.The tolerances for embeded parts and in components of gate are as per IS 9349. The tolerances between Bushing/Bearing /Pin Should confirm to IS 919 ( Part I & II). Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177 .The embedment & gate assembly shall be reasonably water tight, the maximum permissible leakage being not more than 5 liters/min/m wetted length of seal. The surface finish of seal plates should be within the range of 1.6 to 6.3 μm (IS 9349).
MT 131913.00 21804.00
  OUTLET GATE-SLIDING TYPE GATE LEAF - Manufacturing, Erection, Commissioning & Testing      
202 Item No.202 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Gate leaf of Sliding type gate Consisting of following parts. Skin plate skeleton, End Verticals, Guide Brackets, vertical and horizontal stiffeners etc. (As per Drg.) All material used shall conformed to related IS Codes specified in IS 9349. Mild steel confirming to IS 2062.The tolerances for embeded parts and in (Item contd. on next page) components of gate are as per IS 9349. The tolerances between Bushing/Bearing /Pin Should confirm to IS 919 (Part I & II). Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177 .The gates shall be reasonably watertight. Leakage, if any, unless otherwise specified, shall not normally exceed 5 and 10 liter/min/m wetted length of periphery of the sealing surface, for medium and high head gates, respectively as per IS 9349.
MT 110524.00 20893.00
  OUTLET GATE ROLLER TYPE WITH BUSH IN ROLLER - GATE LEAF - Manufacturing, Erection, Commissioning & Testing      
203 Item No.203 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of parts of Roller type gate leaf with bush in the roller consisting of following parts. Skin plate skeleton, End verticals, Guide bracket etc. (As per Drg.) All material used shall conformed to related IS Codes specified in IS 4622. Mild steel confirming to IS 2062.The tolerances for embeded parts of gate are as per IS 4622. Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318),S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). The tolerances between Components & assembly Shall confirm to IS 4623.the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit) & with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference) as per IS 4623.The above items also include Sundry Material, Workshop charges, Labour charges, (Item contd. on next page) Inspection & Quality control charges, Sand blasting with one coat of Zinc rich primer on dry film, should be applied to give total dry film thickness 70 +/- 5 microns. Also 2 coats of solvent less coal tar epoxy paint should be given with a minimum dry film thickness of 150+/- 5 micron per coat should be applied as per IS 14177.The gates shall be reasonably watertight. Leakage, if any, unless otherwise specified, shall not normally exceed 5 and 10 liter/min/m wetted length of periphery of the sealing surface, for medium and high head gates, respectively as per IS 9349.
MT 118454.00 24315.00
  OUTLET GATE ROLLER TYPE WITH BEARING IN ROLLER GATE LEAF - Manufacturing, Erection, Commissioning & Testing      
204 Item No.204 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing of Gate leaf of Roller type gate with Bearing in the roller consisting of following parts. Skin plate skeleton, End verticals, roller bearings, Guide bracket etc.(As per Drg.) All material used shall conformed to related IS Codes specified in IS 4622. Mild steel confirming to IS 2062.The tolerances for components of gate are as per IS 4622The tolerances between Components & assembly Shall confirm to IS 4623.the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit) & with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference) as per IS 4623. Other Material includes C.S. (IS1030), Brass (IS 28), P. Bronze (IS 305), Al. Bronze (IS 318), S.S. (IS 6911), Rubber seal (IS 11855), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints). The above items also include Sundry Material, Workshop charges, Labour charges, Inspection & Quality control charges, Sand blasting with one coat of Zinc rich primer on dry film, should be applied to give total dry film thickness 70 +/- 5 microns. Also 2 coats of slovent less coal tar epoxy paint should be given with a minimum dry film thickness of 150+/- 5 micron per coat should be applied as per IS 14177.The gates shall be reasonably watertight. Leakage, if any, unless otherwise specified, shall not normally exceed 5 and 10 liter/min/m wetted length of periphery of the sealing surface, for medium and high head gates, respectively as per IS 9349.
MT 150595.00 25256.00
  SCREW STEM HOIST - Manufacturing, Erection, Commissioning & Testing      
205 Item No.205 :-
Manufacturing with QAP, fabrication, erection, commissioning & testing with 125 % of rated capacity of Screw stem hoist consisting of Screw stem, Nut, Gear Pinion, Worm wheel, Shaft, Keys etc. All material used shall conformed to IS Codes specified in IS 11228.Mild steel confirming to IS 2062. Other Material includes C.S. (IS1030), P. Bronze (IS 305), Welding electrodes (AWS E6013 for general weld joints & E7018 for X ray quality weld joints).The tolerances between Components & assembly Shall confirm to IS 4623.the fits and tolerances between the bronze bushing & hub shall be H7r6 (Interference fit) & with pin shall be H7f7 (Clearance fit) and for antifriction bearings with hub shall be H7 (Interference) & antifriction bearing with pin shall be r6 (Interference ) as per IS 4623. It includes all materials, Labour charges, machining and machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 95336.00 14159.00
  Straight Needle K.T. Weir Gate- Manufacturing      
206 Item No.206 :-
Manufacturing with QAP & fabrication of KT weir needle gates - straight type size 2.15 x 0.5M- 94 Kg. weight as per relevant Indian Standards with all material, Mild steel confirming to IS 2062, Rubber seal confirming to IS 4623 & Welding electrodes AWS E6013 for general weld joints. It includes all materials, Labour charges, machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 73937.00 6855.00
  Curved Needle K.T. Weir Gate- Manufacturing      
207 Item No.207 :-
Manufacturing with QAP & fabrication of KT weir needle gates - curved type size 2.15 x 0.5M- 74 Kg. weight as per relevant Indian Standards with all material, Mild steel confirming to IS 2062, Rubber seal confirming to IS 4623 & Welding electrodes AWS E6013 for general weld joints. It includes all materials, Labour charges, machinery charges, 1km lead charges of transportation, loading and unloading charges of Gate parts at Site, Inspection & Quality control charges, Sand blasting, Painting with one coat of Zinc rich primer on dry film to give total dry film thickness 70 +/- 5 microns and 2 coats of sloventless coal tar epoxy paint applied to give minimum dry film thickness of 150+/- 5 micron per coat as per IS 14177.
MT 86812.00 8513.00
  Dismantling and fitting of Rubber Seal of Radial Gate 12 x 8 m - 1 No -      
208 Item No.208 (A) :-
Dismantling of old damaged side rubber seal from gate leaf of R.G. 12 x 8 m - 1 No. supplying & fitting new L type side rubber seal confirming to IS 11855-1986 (Updated) and G.I. bolt with double washer including cost of material, labour, machining, sundry material etc complete.
ITEM 72813.00 21501.00
  Item No.208 (B) :-
Dismantling of old damaged Bottom rubber seal from gate leaf of R.G. 12 x 8 m - 1 No. Supplying & fitting flat type bottom rubber seal confirming to IS 11855-1986 (Updated) of size 90x15 mm - 12.2 mtr and G.I. bolt M-20x80 - 97 Nos with double washer including cost of material, labour, machining, sundry material etc complete.
ITEM 37533.00 12357.00
  Repairs to Radial Gate Hoist of 42 MT Capacity - 1 No - (wire rope, cardium compound, gear oil, grease)      
209 Item No.209 (A) :-
Dismantaling of damaged Wire rope, Wire rope socket of 42 MT cap hoist - 1 No. Fixing new Wire rope of Dia 36 mm of falls, confirming to IS 2266. into Wire rope socket confirming to IS 2485, by Zinc (IS 209) Pouring and carrying load test.
(Item contd. on next page) Applying Cardium compound (Servocoat 140) with satisfactory test & Trial. Complete job with material, sundry material & Labour charges.
ITEM 142422.00 11306.00
  Item No.209 (B) :-
Removing Old Cardium Compound of Wire rope of 42 MT cap hoist - 1 No by cleaning agent & Applying new Cardium Compound (Servocoat 140) . Complete job with material, sundry material & Labour charges.
ITEM 9265.00 2688.00
  Item No.209 (C) :-
Draining of Old Oil from RGB & filling with Gear oil GX-90 , Cleaning Gear train by removing old Grease & Applying M.P. Grease to Gear train, Pedestal, Drum axle. Of 42 MT cap hoist -1 No., Complete job with cost of material, sundry material & labour charges.
ITEM 9017.00 2132.00
  Repairs to Vertical Lift Gate (15 x 5 m - 1 No) - (wire rope, rubber seal, track roller) And Repairs to Stop Log gate (12 x 1 m - 1 No.) - (rubber seal, track roller)      
210 Item No.210 (A) :-
Dismantalling of damaged Wire rope of Vertical Lift Gate of size 15 x 5 m - 1 No. Fitting of new Wire rope of Dia 32 mm x 180 Mtr length confirming to IS 2266, with 'D' Clamp Applying Cardium compound (Servocoat - 140) along with satisfactory load test. Complete job with material, sundry material & Labour charges.
ITEM 182538.00 11306.00
  Item No.210 (B) :-
Dismantaling of Damaged Side Rubber Seal from Gate leaf of V.L. Gate size 15 x 5 Mtr - 1 No. and fitting of new "Z" type Side rubber seal confirming to IS 11855-1986, along, with G. I. Bolt , with Double Washer and Nut with satisfactory test & trial. Complete job with material, sundry material & labour charges.
ITEM 44035.00 14641.00
  Item No.210 (C) :-
Dismantalling of Damaged Bottom Rubber Seal from Gate leaf of V. L. Gate 15 x 5 m - 1 No & fitting of new Flat type Bottom rubber seal confirming to IS 11855-1986 with G. I. Bolt with Double Washer and Nut with satisfactory test & trial. Complete job with material, sundry material & labour charges.
ITEM 39283.00 8649.00
  Item No.210 (D) :-
Dismantaling & Cleaning of Track Roller - 8 Nos, Guide Rollers - 4 Nos. & Equilliser Assembly Rollers of Vertical Lift Gate of size 15 x 5 m - 1 No. Refitting after applying M.P. Grease Complete job with material, sundry material & labour charges.
ITEM 6613.00 4264.00
  Item No.210 (E) :-
Dismantalling & Cleaning of Track Roller - 4 Nos of stoplog Gate 12 x 1 Mtr - 1 No. and refitting with M. P. Grease - 4 Kg & Damaged 'O' Ring - 12.00 Mtr. Complete Job with Material, sundry material & Labour Charges.
ITEM 4669.00 1607.00
  Item No.210 (F) :-
Dismantling of damaged side rubber seal from gate leaf of stoplog gate of size 12 x 1 m -1 No, on Maintenance Platform and fitting new Hollow type side rubber seal confirming to IS11855 / 1986 and G. I. Bolt with Double Washer and Nut with satisfactory test & trial. Complete job with material & labour charges.
ITEM 19227.00 6548.00
  Item No.210 (G) :-
Dismantaling of damaged Bottom rubber seal from gate leaf of stoplog gate of size 12 x 1 m - 1 No. and fitting of new flat type Rubber seal confirming to IS 11855- 1986, and G. I. Bolt with Double Washer and Nut with satisfactory test & trial. Complete job with material, sundry material & labour charges.
ITEM 33428.00 11306.00
  Repairs to Goliath Crane 16 MT capacity - (wire rope, cardium compound, zink pouring] gear oil, greasing) -      
211 Item No.211 (A) :-
Dismantaling of damaged Wire rope, Wire rope socket of 16 MT cap Goliath Crane -1 No. Fixing new wire rope of 19 mm dia. of falls, confirming to IS 2266 into Wire Rope socket confirming to IS 2485 by Zinc (IS 209) pouring and carrying load test. Applying Cardium compound. (Servocoat 140) with satisfactory test & Trial. Complete job with material & Labour charges.
ITEM 55145.00 9730.00
  Item No.211 (B) :-
Removing Old Cardium Compound of wire rope (100 Mtrs) of 16 MT cap Goliath Crane - 1 No., by cleaning Agent, Applying new Cardium Compound (Servocoat 140) Complete job with material, sundry material & Labour charges.
ITEM 7034.00 2688.00
  Item No.211 (C) :-
Draining of Old Oil from RGB - 3 Nos. (O:600 - 1No. & O:400 - 2 Nos.) Filling with new gear oil GX 90 , Cleaning Gear train by removing old grease, Applying M.P. Grease to Gear train, Pedastal, Drum axle. etc to 16 MT Goliath crane - 1 No. Complete job with cost of material, sundry material & labour charges.
ITEM 8988.00 3213.00
  Repairs to Roller type Gate 0.9 x 0.9 m and 1.2 x 1.2 m -      
212 Item No.212 (A) :-
Dismantling of Roller type Gate leaf of size 0.9 x 0.9 Mtr / 1.2 x 1.2 Mtr (20 MWH) and hoist assembly - 1 No. lifting of the same up-to Platform for Repair work and lowering on Sill Beam. Complete job including cost of sundry material and labour charges.
ITEM 13880.00 7538.00
  Item No.212 (B) :-
Dismantaling of Damaged Side Rubber seal - 1 Mtr from Gate Leaf & fitting of new Musical note type Side rubber seal (confirms to IS: 11855 / 1986 (Updated)) with Nut Bolts Complete job with Material, Sundry material, & Labour charges.
ITEM 19436.00 6487.00
  Item No.212 (C) :-
Dismantaling of Damaged Top Rubber seal - 1 Mtr from Gate Leaf & fitting of new Double Stem type Top rubber seal (confirms to IS: 11855 / 1986 (Updated)) with Nut Bolts Complete job with Material, Sundry material, & Labour charges.
ITEM 12056.00 3243.00
  Item No.212 (D) :-
Dismantaling of Damaged Bottom Rubber seal - 1 Mtr from Gate Leaf & fitting of new Plain Flat type Bottom rubber seal (confirms to IS: 11855 / 1986) with Nut Bolts Complete job with Material, Sundry material, & Labour charges.
ITEM 9038.00 3243.00
  Item No.212 (E) :-
Dismantaling & Cleaning of Track Rollers (4 Nos), of Roller type Gate of size 0.9 x 0.9 M / 1.2 x 1.2 Mtr (20 MWH) - 1 No.. Refitting with M.P. Grease Complete job including cost of sundry material and labour charges. (Excluding Cost of New Bearing / Bush).
ITEM 3288.00 2132.00
213 Item No.213 :-
Dismantling Square threaded / "V" threaded Stem Rod 90 mm dia - 1 No. of 15 MT capacity Screw Stem Hoist. Removing bend on hydraulic Press machine, Threads Cleaning and refitting of the same. Complete job including cost of sundry material, Machinery and labour charges. (Excluding new material charges)
ITEM 7251.00 2688.00

*****