OTHER MATERIALS -1



ANNEXURE-VI
RATES OF OTHER CONSTRUCTION MATERIALS
Note: No extra on cost, conveyance charges shall be allowed for all the items included under this category. The rates approved therein are applicable at site of work
SI. No. Name of Material Unit Basic Rate approved for the year 2019-2020 (w.e.f. 17.06.2019)
1 Water Proofing Compound Kg 41.50
2 Mild Steel Flats of all sizes Kg 40.45
3 Mild Steel Square Rods of all sizes Kg 40.45
4 First Quality Design Ceramic Tiles of all Colours    
i 305mm x 305mm x 6mm Each 45.00
ii 200mm x 200mm x 6mm Each 19.80
iii 200mm x 100mm x 6mm Each 10.70
5 First Quality Plain Ceramic Tiles of all colours    
i 305mm x 305mm x 6mm Each 32.20
ii 200mm x 200mm x 6mm Each 14.40
iii 200mm x 100mm x 6mm Each 7.40
6 Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm Each 53.00
7 Solar Reflective Ceramic Tiles of size    
a 305mm x 305mm x 7mm thick sqm. 464.00
b 305mm x 240mm x 6mm thick sqm. 383.00
8 Dadooing Ceramic Tiles of size 300mm x 450mm x 8mm Each 57.20
9 Dadooing Ceramic Tiles of size 300mm x 600mm x 10mm Each 85.00
10 First Quality White Glazed Tiles    
i 150mm x 150mm x 6mm Each 7.70
ii 100mm x 200mm x 6mm Each 6.70
11 First Quality Colour Glazed Tiles    
i 150mm x 150mm x 6mm Each 8.90
ii 100mm x 200mm x 6mm Each 7.70
12 First Quality Colour Glazed Tiles with Printed Design    
i 150mm x 150mm x 6mm Each 10.50
ii 100mm x 200mm x 6mm Each 9.50
13 Colour Designed Glazed Tiles 300 x 200 x 6mm Each 28.30
14 Stain Free Nano Polish Vitrified Tiles 600 x 600 x 8mm sqm. 603.00
15 Double Charged Vitrified Tiles 600 x 600 x 8mm sqm. 900.00
16 Double Charged Vitrified Tiles 800 x 800 x 10mm sqm. 1150.00
17 Pre-polished Concrete Anti-Skid Step Tiles of 20mm thick sq.m. 599.00
18 Rubber Moulded Hydraulic Pressed Paver Block    
a 83mm thick sqm. 537.00
b 63mm thick sqm. 447.00
19 TAMIN Paver Block of size - Supply at site    
a 60mm thick sft. 50.10
b 80mm thick sft. 60.00
  New Items    
20 Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person sqm. 2000.00
21 Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete. sqm. 430.00
22 White Cement Kg 22.00
23 Colour Cement (White Cement mixed with Colouring Pigments) Kg 26.60
24 Multi-Colour Marble Chips of all grades / sizes Bag 88.60
25 White Marble Slab (Adanga) 18mm to 20mm Thick    
i 4'0" x 2'0" and above sqm. 1365.00
ii 2'0" x 2'0" or 2'0" x 1'0" or 1'0" x1'0" sqm. 682.00
26 Granite Tiles - (Superfine Polished with Machine Cut Edges) of size 2'0" x 1,0" or 1,0" x 1'0" or 1`0" x 0'6" of 10 mm thick    
a Jet Black sqm. 844.00
b Ruby Red, Raw Silk sqm. 756.00
c Sinthetic Grey, Paradise and similar varieties sqm. 714.00
27 Granite Slabs (Super Fine Polished with Machine Cut Edges) of sizes 4'x2' and above 18mm to 20mm thick    
a Jet Black sqm. 1690.00
b Ruby Red, Raw Silk sqm. 1580.00
c Sinthetic Grey, Paradise and similar varieties sqm. 1420.00
d Fine Polished Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 1470.00
e Fine Polished Blue Pearl Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 7350.00
28 Flamed Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 1780.00
29 Flamed Ruby Red Granite Slab 1200mm x 600mm, 16mm to 18mm Thick sqm. 1890.00
  New Items    
1 Nosing for Granite Slab    
a Single Nosing RM 190.00
b Double Nosing RM 360.00
30 Polished Shahabad Stone Slabs 20mm thick with Machine Cut Edges of size below 2'0" x 2'0" sqm.  309.00
31 Polished Shahabad Stone Slabs of 20mm thick with Machine Cut Edges of size 2'0" x 2'0" and above sqm. 367.00
32 Polished Rajasthan Kota Stone Slabs of 20mm thick with Machine Cut Edges of size below 2'0" x 2'0" sqm. 472.00
33 Polished Rajasthan Kota Stone Slabs of 20mm thick with Machine Cut Edges of size 2'0" x 2'0" and above sqm. 535.00
34 Dolphur Stone Slabs - Semi Polished with Machine Cut Edges of all sizes    
a 40mm thick sqm. 408.00
b 20mm thick sqm. 372.00
  New Items    
35 PVC Trims (Beading) RM 90.00
36 Terracota Jally of size 20 x 20 x 0.75mm Each 38.00
37 Aluminium Strips of size 40mm wide x 1.5mm thick RM 32.30
38 Brass Strips of size 40mm wide x 1.5mm thick RM 67.30
39 Glass Strips of size 40mm wide and 4mm thick RM 15.30
40 Marblex Tiles 3mm thick sqm. 664.00
41 Red Oxide - Superior quality for floor finish Kg 141.00
42 Decorative Pressed Tiles of 12mm thick of all sizes and shapes sqm. 1045.00
43 Exterior Emulsion Paint - Water Based Primer (Liquid) Litre 147.00
44 Alkali Resistant Distemper Primer Litre 131.70
45 Sandtex Matt Litre 154.00
46 Vinaratex or Equivalent Textured Coat sqm. 198.00
47 Best Lac Polish / French Polish Litre 257.00
48 Varnish Litre 264.00
49 Cotton Waste Kg 10.10
50 Cement Based Hydraulically Pressed Anti skid Tiles (Pattern Design) - 20mm thick sqm. 496.00
51 Marble Powder Kg 4.45
52 Polishing Stone    
i Rough Each 65.20
ii Medium Each 87.10
iii Fine / Nice Each 99.70
53 Oxalic Acid Kg 37.80
54 Tupentine Litre 23.10
55 Mansion polish 400 gram 144.90
56 Poly Sulphide Kg 171.90
57 Primer for Expansion Joints Kg 147.90
58 Filler Material sqm. 141.00
59 Bond Breaker RM 3.65
60 PVC Water Bar 150mm wide with Singlel Bulb RM 280.00
61 Plain GI Sheet 0.8mm thick (22 Gauge) sqm. 354.00
62 Phil Plug Each 4.90
63 GI Screws    
i 30mm x 6mm Each 1.25
ii 19mm x 6mm Each 0.79
64 GI Limpet / Cup Washers Each 1.84
65 Bitumen Washers 15mm dia Each 1.10
66 Asbestos Cement Pipe - 100mm dia 3 RM 139.90
. 67 AC Shoe - 100mm dia Each 44.40
68 AC Bend - 100mm dia Each 50.80
69 AC Cylindrical Cowl - 100mm dia Each 76.30
70 CI Brackets for AC Pipe 100mm dia Each 19.50
71 CI Grating - 100mm dia Each 31.20
72 Asbestos Cement Fully Corrugated Sheet - 6mm thick sqm. 184.20
73 Asbestos cement plain sheet    
i 6mm thick sqm. 165.30
ii 4mm thick sqm. 114.50
74 Asbestos Cement Adjustable Ridges Pair 190.70
75 GI "J" or "L" Bolts with Nuts 6mm dia Each 3.80
76 Steel - Special Extruded Sections for Steel Windows and Ventilators conforming to ISS 7452 / 1990 including fabrication charges Kg 60.90
77 CRCA Pressed Steel Box Section 18 Gauge or 1.25mm thick for Door Frames including providing holes and fixing wooden blocks for fixing furniture and fittings    
a With one coat of Red Oxide priming coat RM 350.00
b With Powder Coated Primer RM 373.00
78 Aluminium Extruded Sections (for Doors, Windows, Ventilartors, Partitions, False Ceiling etc) including charges for anodising for 15 micron thickness    
a Natural Colour Matt Finish Kg 287.00
b With Powder Coating of any colours Kg 307.00
79 Alumninum Extruded Box Section for Staircase Hand Rails including charges for anodising for 15 micron thickness - Natural colour matt finish Kg 359.00
80 Rubber Beading for Aluminium Glazed Doors RM 37.25
81 Rubber Beading for Aluminium Glazed windows RM 28.40
82 PVC / Woollen Felt for Aluminium Doors 6mm thick RM 7.50
83 Pivot for Aluminium Door Set 146.00
84 Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded Section Body Tubular Type Universal Hydraulic Door Closer with Double Speed Adjustment like HARDWYN (make) IGAZEL` (or) Equivalent (with ISI Monogram) Each 890.00
85 Hydraulic Floor Springs of various sizes, Double Acton Hydraulic Floor Spring of approved quality, brand, manufacture asper BIS Standards for doors including cost of cutting floors as required, embedding in to floors and stainless steel cover plates with aluminium pivot and single piece MS sheet outer box with side plate etc., capaple of taking upto 130 kg. weight from door shutter, like HARDWYN make (U-32) or its Euivalent with ISI monogram. Each 2035.00
86 Lock for Aluminium Doors Each 251.00
87 Lock for Aluminium Sliding Windows Each 62.80
88 Aluminium Grill of Standard Pattern (Diamond Shape) - 10mm thick including 'F' (or) 'H' Section sqm. 1835.00
89 Aluminium Grill of Standard Pattern (Diamond Shape) - 6mm thick including 'F' (or) 'H' Section sqm. 1485.00
90 Bolts and Nuts 10mm dia for False Ceiling Each 5.50
91 Rawl Plugs for False Ceiling Each 9.35
92 PVC Roller for Sliding Windows Each 13.75
93 Synthetic Resin - Fevicol or Equivalent (Phenol Formal Dehide Based Resin) Kg 194.00
94 Butt Hinges with Nylon Washers of various sizes of Length and Width (with required screws)    
a 125mm x 30mm Each 78.40
b 100mm x 30mm Each 62.90
c 75mm x 30mm Each 43.20
d 50mm x 30mm Each 34.80
95 Tower Bolts of various lengths and diametre (with required screws)    
a 400mm long and 12mm dia Each 148.30
b 300mm long and 12mm dia Each 114.10
c 250mm long and 12mm dia Each 85.50
d 200mm long and 12mm dia Each 71.90
e 150mm long and 12mm dia Each 56.70
f 100mm long and 10mm dia Each 49.80
g 75mm long and 10mm dia Each 34.80
96 Aldrops of following lengths and diametre with required screws, bolts and nuts    
a 300mm long and 16mm dia Each 183.40
b 250mm long and 16mm dia Each 158.20
c 200mm long and 16mm dia Each 107.10
d 200mm long and 12mm dia Each 88.90
97 Handles "D" type of various sizes with required screws    
a 200mm long Each 56.20
b 150mm long Each 50.40
c 100mm long Each 30.90
98 Ornamental Handles of various sizes with required screws    
a 200mm long Each 144.90
b 150mm long Each 96.60
c 100mm long Each 53.30
99 Aluminium Door Stopper with Rubber Bush with required screws Each 43.80
100 Rubber Bush - 40mm dia and 60mm long with required screws Each 22.50
101 Mortice Lock (Godrej or Equivalent) with required screws with 3 Keys    
a With Night latch Each 525.00
b Without Night latch Each 391.00
c Wire Nails Kg 62.20
102 Teakwood Beading    
a 15mm x 12mm RM 15.00
b 35mm x 12mm RM 38.10
103 Teakwood Beading (Ordinary)    
a 30mm x 12mm RM 31.60
b 25mm x 12mm RM 25.40
104 Teakwood Beading - Ornamental / Design    
a 40mm x 12mm RM 88.90
b 40mm x 15mm RM 101.80
c 25mm x 12mm RM 69.60
d 15mm x 12mm RM 47.90
105 Medium Desity Fibre (MDF) Board - Exterior Grade, both sides pre-lamiated including external lipping with kiln dried soft wood 35mm thick sqm. 2120.00
106 Medium Density Fibre (MDF) Board - Exterior Grade - both sides pre-laminated, 12mm thick sqm. 1020.00
107 MDF Board Exterior Grade - Plain including external lipping with kiln dried soft wood    
i 35mm thick sqm. 1730.00
ii 30mm thick sqm. 1595.00
108 Medium Density Fibre (MDF) Board 12mm thick Exterior Grade with Melamine finish    
a One Side Melamine Finish sqm. 1080.00
b Both Sides Melamine Finish sqm. 1215.00
109 Medium Density Fibre (MDF) Board - Exterior Grade - Plain with teakwook external lipping alround    
a 35mm thick sqm. 1860.00
b 30mm thick sqm. 1650.00
110 Solid Core Flush Shutters with teakply on both side with teakwook lipping alround 35mm thick sqm. 2190.00
111 Solid Core Flush Shutters with teakply on one side and commercial ply on other side with teak wook lipping alround 35mm thick sqm. 1925.00
112 Solid Core Flush shutters with commercial ply on both side with teakwook lipping alround 35mm thick sqm. 1650.00
  New Item    
113 Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work. sqm. 4900.00
114 Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter    
a Solid panel PVC door with frame sqm. 2800.00
b Solid Panel PVC Door without Frame sqm. 2360.00
  New Item    
115 Supplying and fixing of PVC Sliding Door with Roller sqm. 3000.00
116 a FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers sqm. 3880.00
b Excluding door frames sqm. 2980.00
117 a PVC Panelled door Shutters Hollow Type - 200mm x 20mm panels with 1mm wall thickness for panels and styles and rails of suitable size with 2mm wall thickness suitably reinforced using MS Angle / Flat including cost of necessary aluminium hinges and other furniture fittings sqm. 1995.00
b Excluding Door Frames sqm. 1685.00
118 RCC Door Frame of 100mm x 65mm cross sectional size with necessary rebate for housing the shutters, manufactured with cement concrete of grade not less than M20 using 10mm and below graded stone jelly and using steel reinforcement as per CE (B) Circular instructions RM 273.00
119 Stainless Steel (Salem Stainless Steel) Door Frame
(Box Section using Stainless Steel Plate of 1mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc
RM 892.00
120 Stainless Steel (Salem Stainless Steel) Door Frame
(Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc
RM 1205.00
121 Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc    
A ROLLING SHUTTERS (WITH ISI MONOGRAM)    
a Manually Operated (up to 8 sqm. Area) sqm. 2110.00
b Gear Operated Type (from 8 sqm. to 12 sqm. Area) sqm. 2350.00
c Electrically Operated Type (exceeding 12 sqm. Area) sqm. 2550.00
B ROLLING GRILLS (WITH ISI MONOGRAM)    
a Manually Operated (up to 8 sqm. Area) sqm. 2150.00
b Gear Operated Type (from 8 sqm. to 12 sqm. Area) sqm. 2420.00
c Electrically Operated Type (exceeding 12 sqm. Area) sqm. 2690.00
122 Barbed Wire - 10 Gauge - Two Ply and Four Pronged (Galvanised) 1 Kg or 6 RM 60.30
123 Chain Link - 2" x 2" using 10 Gauge Galvanised Iron Wire (of all sizes) sqm. 155.70
124 Pin Headed / Fluted / Figured Glass 3mm thick sqm. 220.00
125 Plain Glass - 4mm thick sqm. 298.00
126 Plain Sheet Glass - 5.5mm thick sqm. 352.00
127 Metal Screws (for Aluminium Doors, Windows etc)    
i 75mm x 8mm Each 2.15
ii 38mm x 6mm Each 1.50
iii 19mm x 8mm Each 1.05
iv 19mm x 6mm Each 0.79
128 Cement Paint (First Quality) Kg 48.50
129 Oil Bound Distemper Kg 71.70
130 Acrylic Distermper Kg 82.80
131 Primer for Plastic Emulsion Paint Litre 143.30
132 Plastic Emulsion Paint (First Quality) Litre 287.00
133 Wood Primer Litre 143.30
134 Synthetic Enamel Paint for Wood Work Litre 232.00
135 Red Oxide Primer for Iron Work Litre 133.00
136 Synthetic Enamel Paint for Iron Work Litre 221.00
137 Melamine Polish Sqm. 630.00
  New Item    
138 Exterior Emulsion Paint Litre 295.00
139 Painting the wall with Texture Finish Paint including labour charges sqm. 400.00
140 Providing Wall Putty including labour charges sqm. 50.00
141 300mm dia RCC Hume Pipe RM 2185.00
142 GI Pipes "B" Class    
i 65mm dia RM 242.00
ii 50mm dia RM 207.00
iii 40mm dia RM 161.60
iv 32mm dia RM 149.90
v 25mm dia RM 126.80
vi 20mm dia RM 97.70
vii 15mm dia RM 69.20
143 GI Specials    
A Union    
i 50mm dia Each 263.70
ii 40mm dia Each 195.60
iii 32mm dia Each 126.30
iv 25mm dia Each 97.70
v 20mm dia Each 69.20
vi 15mm dia Each 57.60
B GI Elbow    
  50mm dia Each 126.80
ii 40mm dia Each 97.70
iii 32mm dia Each 86.20
iv 25mm dia Each 57.60
v 20mm dia Each 25.20
vi 15mm dia Each 15.80
C GI Bend    
i 50mm dia Each 115.20
ii 40mm dia Each 86.20
iii 32mm dia Each 69.20
iv 25mm dia Each 51.50
v 20mm dia Each 23.00
vi 15mm dia Each 13.50
D GI TEE    
i 50mm dia Each 138.50
ii 40mm dia Each 109.20
iii 32mm dia Each 97.70
iv 25mm dia Each 80.60
v 20mm dia Each 34.40
vi 15mm dia Each 28.40
E GI COUPLING    
i 50mm dia Each 69.20
ii 40mm dia Each 57.60
iii 32mm dia Each 46.10
iv 25mm dia Each 28.40
v 20mm dia Each 15.80
vi 15mm dia Each 13.50
F GI REDUCER    
i 50mm x 40mm dia Each 92.30
ii 40mm x 32mm dia Each 69.20
iii 32mm x 25mm dia Each 51.50
iv 25mm x 20mm dia Each 28.40
v 20mm x 15mm dia Each 20.10
vi 40mm x 25mm dia Each 51.50
vii 32mm x 20mm dia Each 40.00
G GI REDUCER ELBOW    
i 50mm x 40mm dia Each 109.20
ii 40mm x 32mm dia Each 92.30
iii 32mm x 25mm dia Each 69.20
iv 25mm x 20mm dia Each 51.50
v 20mm x 15mm dia Each 40.00
vi 40mm x 25mm dia Each 72.00
vii 32mm x 20mm dia Each 57.10
H GI REDUCER TEE    
i 50mm x 40mm dia Each 138.50
ii 40mm x 32mm dia Each 115.20
iii 32mm x 25mm dia Each 97.70
iv 25mm x 20mm dia Each 74.60
v 20mm x 15mm dia Each 69.20
vi 40mm x 25mm dia Each 103.70
vii 32mm x 20mm dia Each 80.60
I GI HEX NIPPLE    
i 50mm dia Each 86.20
ii 40mm dia Each 69.20
iii 32mm dia Each 57.60
iv 25mm dia Each 43.30
v 20mm dia Each 34.40
vi 15mm dia Each 23.00
144 Gun Metal Gate Valve (Heavy Duty)    
i 65mm dia Each 1480.00
ii 50mm dia Each 1205.00
iii 40mm dia Each 950.00
iv 32mm dia Each 739.00
v 25mm dia Each 577.00
vi 20mm dia Each 341.00
  Note: Gate Valves should be used only in delivery line to OHT Scour Pipe in OHT (for cleaning of OHT) where pressure pumping is involved. In all other cases only wheel valve should be used    
145 Gun Metal Wheel Valve (Heavy Duty)    
i 40mm dia Each 634.00
ii 32mm dia Each 499.00
iii 25mm dia Each 342.00
iv 20mm dia Each 235.00
v 15mm dia Each 166.00
146 Brass Chromium Plated Screw Down Tap 15 / 12mm dia (Heavy Type) Each 200.00
147 Brass Chromium Plated Pillar Tap (Heavy Type) - 15 / 12mm dia Each 263.00
148 PVC Screw Down Tap Heavy Type 20mm dia Each 79.40
149 PVC Screw Down Tap Heavy Type 15mm dia Each 61.40
150 Chromium Plated Stop Cock 15mm dia Each 147.00
151 Brass Chromium Plated Shower Rose - 100mm dia Each 189.00
  New Item    
152 CP Wall Mixture Tap 3 in 1 system with Hand Showers Each 4025.00
153 CP Two Way Bib Cock with Health Faucet Each 2000.00
154 CP Shower Arm with Overhead Shower Rose Each 1150.00
155 Wooden Plug, Clamp and Screws Set 11.90
156 Shellac 100 gram 18.00
157 PVC Adhesive (Solution) 100 gram 33.70
158 Thread Ball Each 3.50
  New Item    
159 CP Heavy Duty Bottle Trap 32mm Each 1075.00
160 CP Angle Cock Tap Each 755.00
161 Oriya Type Indian Water Closet 580mm x 440mm with "P" or "S" Trap    
i White Set 1170.00
ii Colour Set 1490.00
162 European Water Closet with "P" or "5" Trap with Double Flapped Seat and Seat Cover with Brass Hinges and 10 litre capacity PVC Low Level Flusing Tank with all internal fittings    
i White Set 3000.00
ii Colour Set 3390.00
163 European Water Closet with "P" or "S" Trap with Double Flapped Seat and Seat Cover with Brass Hinges and 12.5 litre capacity Porcelain Low Level Flusing Tank with all internal fittings    
i White Set 4230.00
ii Colour Set 5090.00
164 PVC low level flushing tank with all internal    
fittings (wall mounting type)
a White - 10 litre capacity Set 847.00
b White - 7.5 litre capacity Set 647.00
c Colour - 10 litre capacity Set 959.00
d Colour - 7.5 litre capacity Set 762.00
165 PVC Water Tank Litre 8.60
  New Item    
166 SS Elbow Action Tap of size 15mm Each 1500.00
167 SS Heavy Duty Long Body Tap 15mm Each 1500.00
168 SS Swan Neck Tap Each 1000.00
169 Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mm dia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc    
i White without Pedastal Set 1625.00
ii White with Pedastal Set 1955.00
iii Colour without Pedastal Set 2175.00
iv Colour with Pedastal Set 2405.00
170 White Porcelain Sink of size 600mm x 450mm x 200mm with 32mm dia 'B' Class GI Waste Water Pipe and 32mm dia CP Waste Coupling Set 2085.00
171 Cuddapah Slab Sink of size 600mm x 450mm x 200mm with 32mm dia 'B' Class GI Waste Water Pipe & 32mm dia CP Waste Coupling Set 748.00
172 Cuddapah Slab Sink of size 600mm x 600mm x 200mm with 32mm dia 'B' Class G.I. waste water pipe & 32mm dia C.P. waste coupling. Set 991.00
173 Lipped Mouth Porcelain Flat Back Urinal with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple etc.    
i White Set 913.00
ii Colour Set 1045.00
  New Item    
174 Supplying and fixing of SS Sink of size 1200 x 550 x 180mm Each 18000.00
175 Supplying and fixing of Granite Sink of size 600 x 600 x 250mm Each 4026.00
176 Supplying and fixing of Ornamental Type White Glazed Porcelain Corner 'L' Type Wash Hand Basin of size 350mm Each 3450.00
177 Supplying and fixing of Oval Shape Wash Hand Basin of size 560 x 450mm Each 2815.00
178 Supplying and fixing of White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm Each 9775.00
179 Porcelain Soap Dish of size 150mm x 150mm x 50mm    
i White Each 190.50
ii Colour Each 261.00
180 Brass Chromium Plated Soap Tray of size 150mm x 100mm Each 160.30
181 Brass Chromium Plated Towel Rail 60cm long and 20mm dia with Brackets Set 261.20
  New Item    
182 SS Towel Rack 600mm long with Lower Hanger Each 1500.00
183 Anodised Aluminium Towel Rail 60cm long and 20mm dia with Brackets Set 128.00
184 PVC / Fibre Glass Framed 5.5mm thick Mirror, Shelf Type with Hard Board Backing    
i 600mm x 450mm Each 462.00
ii 500mm x 400mm Each 372.00
  New Item    
185 Special Type Mirror of size 1000 x 780mm Each 2500.00
186 Stoneware Gully Trap of size 150mm x 100m with Cast Iron Double Gratings Each 165.50
187 Cast Iron Nahini / Floor Trap with Stainless Steel Grating    
i 100mm x 75mm Each 271.50
ii 75mm x 50mm Each 212.70
188 PVC Nahini / Floor Trap with PVC Grating    
i 100mm x 75mm Each 150.00
ii 75mm x 50mm Each 131.40
189 First Quality Cast Iron Pipe    
i 150mm Dia RM 985.00
ii 100mm Dia RM 594.00
iii 75mm Dia RM 474.00
iv 50mm Dia RM 336.00
190 First Quality Cast Iron Specials    
A Plain Bend    
i 150mm dia Each 533.00
ii 100mm dia Each 260.00
iii 75mm dia Each 200.00
iv 50mm dia Each 153.00
B Bend with Door    
i 150mm dia Each 617.00
ii 100mm dia Each 312.00
iii 75mm dia Each 260.00
iv 50mm dia Each 206.00
C Plain TEE    
i 150mm dia Each 1068.00
ii 100mm dia Each 474.00
iii 75mm dia Each 324.00
iv 50mm dia Each 223.00
D TEE with Door    
i 150mm dia Each 1128.00
ii 100mm dia Each 546.00
iii 75mm dia Each 379.00
iv 50mm dia Each 271.00
E "Y" Junction with Door (Single)    
i 150mm dia Each 1186.00
ii 100mm dia Each 594.00
iii 75mm dia Each 414.00
iv 50mm dia Each 296.00
F "Y" Junction with Door (Double)    
i 150mm dia Each 1307.00
ii 100mm dia Each 664.00
iii 75mm dia Each 498.00
G COWL    
i 150mm dia Each 324.00
ii 100mm dia Each 195.00
iii 75mm dia Each 130.00
iv 50mm dia Each 100.00
191 Stoneware Pipe    
i 150mm dia Each (0.6.RM) 99.20
ii 100mm dia Each (0.6.RM) 61.60
192 Stoneware Specials    
A Stoneware TEE    
i 150mm dia Each 161.30
ii 100mm dia Each 124.40
B Stoneware Bend    
i 150mm dia Each 136.70
ii 100mm dia Each 98.70
C Stoneware "Y" Junction    
i 150mm dia Each 166.40
ii 100mm dia Each 123.90
193 Spun Yarn Kg 12.80
194 Hemp Yarn Kg 11.50
195 Gunny Tape / Kithan sqm. 11.50
196 Tar Kg 39.90
197 Bitumen Felt 15mm thick Pad sqm. 228.00
198 Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level    
a Using Hilux Board Plain Sheets (10mm thick) sqm. 945.00
b Using Perforated Sheets (10mm thick) sqm. 967.00
199 Supplying and laying Glass Wool for insulation including necessary packing materials    
a Using 50mm thick Glass Wool sqm. 382.00
b Using 25mm thick Glass Wool sqm. 203.00
  New Items    
200 Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush.
Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed.
Apply first coat of polymer modified cementitious
slurry by brush on wet cleaned surface. After drying,
second coat shall be applied on the first coat as
directed by the departmental officers etc. The rate
inclusive of cost of materials and labour, etc.,
complete.
sqm. 320.00
201 Providing Cornice Work for Gyp Board False Ceiling RM 185.00
202 8mm thick Calcium Silicate Board Designed and Perforated for False Ceiling sqm. 1500.00
203 Termite Proof/Water Proof Plywood 19mm thick sqm. 1300.00
204 Laminated Sheet 0.8mm thick (inside) sqm. 240.00
205 Laminated Sheet 1mm thick (outside) sqm. 400.00
206 Vitrified Tiles of size 600 x 600 x 8mm sqm. Deleted
207 Squatting Urinal Set 442.00
208 CI Brackets for fixing the Sink Set 104.90
209 Swan Neck Tap Each 246.00
210 Brass Screws (30 x 6mm) Each 2.35
211 Brass Screws (75 x 10mm) Each 4.75
212 Special Clamp, Teakwood Plugs and Screws Set 21.00
213 PVC Clamp, Teakwood Plugs and Screws Set 8.30
214 Teakwood Plug Each 1.05
215 Teakwood Plug (50 x 50 x 100mm) Each 5.25
216 Manhole Cover 60 x 60cm (Heavy Duty) with Frame Each 1810.00
217 Welding Charges    
a 50mm Each 2.05
b 40mm Each 1.60
218 Add for Painting / Tarring for Hex Nipple Each 2.75
219 Labour Charges for fixing Cuddapah Slab to Cup-Board sqm 44.70
220 Hire Charges for Polishing Machinery Day 222.00
221 Electricity Charges Unit 11.60
222 Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm "P" or "S" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting Each 4925.00
223 Supplying and fixing in position White / Colour Special Delux Model Glazed Cascade Type Parryware / Hindware / Equivalent Wall Mounted European Water Closet of best quality and approved make with 100mm "P" or "5" trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) with 10 litres capacity flushing tank with all internal dual flush fittings with normal seat cover Each 5775.00
Wall Fitting    
224 Vinyl Flooring 2mm thick sqm. 537.00
225 Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete sqm. 5375.00
226 Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete RM 1790.00
227 PVC mould CI Steps for Sump Each 224.00
228 Vertical Blinds    
a Ordinary sqm. 896.00
b Premium sqm. 1344.00
229 Stainless Steel Health Faucet Each 985.00
230 High Density Fibre (HDF) Board sqm. 2147.  00
231 Providing and fixing of Aluminium Composite Panel (ACP) 4 sided having 50 x 25 x 1.50mm frame work vertical and horizontals out of specially designed extruded sections withstand wind pressure of 180 Kg/sq.m and fabricated fixed at all level elevation and heights. The extruded section cutting and fixing required space extruded section shall be of 6063 and alloy of BSH 9 confirming T is - 63400 rate shall included to fix the main frame with necessary clamps,fasteners, bolt nuts etc. The main frame of extruded section shall be of 22843 & 22739 (H9) grade conforming to BS 4174 (or) IS 8147. Rate shall included 4mm thick ACP sheet (0.25 + 3.5 + 0.25) alstrong or equivalent fixing with spacer tape and the ACP sheet bounded with special type structural sealant of dow corning 789 or equivalent in dust free conditions the gaps between ACP sheet to be filed with whether sealant and backer rod or 12mm foam sheet to ensure water and air tightness in all complete complying with standard specification as directed by the departmental officer sqm. 4265.00
232 Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere sqm. 4700.00
233 Bitumen Pad    
a 12mm thick sqm. 467.00
b 20mm thick sqm. 699.00
234 Pre-Painted Galvanized Iron Window (Airtight Model) with Grill
Specification: Providing and fixing for Pre-Painted GI Window fabricated from roll formed sections made of Galvanized Iron Color Coated / Powder Coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 GSM / sqm.) with total coated thickness of 0.6mm. Coated Sections should be with Primer Coat of Epoxy Primer of 5-7 microns thick, finished paint with a polyester paint of 12-16 microns thich and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick. Sections for shutter shuld be of 46 x 46mm and external frame should be of 46 x 52mm. Section for glass beading should be of 18 x 25mm and centre mullion should be of 46 x 70mm. The frame and shutter sections should be cut to length and miter joined with corner bracket made of glass filled Nylon. Mullion Section should be joined with Frame / Mullion using Nylon Mullion Cap Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter between frame and galzed shutter and both sides of fixed glass. Handle made of high grade Aluminum Powder coated and with nylon receiver-1 each shutter. Friction hinge-1 set for each shutter. Glass shutter and fixing glass portions should be provided with a Acrylic Sheet of minimum 6mm thickness. Windows should be provided with grill made of 10mm square. MS Bars provided with grill made of 10mm square. MS Bars provided with grill made of 10mm square. MS Bars welded at 4" intervals centre to centre, 5mm x 12mm MS flat. Total grill unit should be powder coated and fixed to window frame with Rivets. The above frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. The Pre-Painted Galanized Iron Window should be got approved from the Executive Engineer before use on work
sqm. Deleted
  New Items    
235 Providing Strong Room Door for Sub-Treasuries Each 290000.00
236 Pre-painted Galvanized Iron Windows (Air Tight Model) with Grill and Glass: Providing and fixing Ajanta Cave Model Window fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.60mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: Sections for shutter should be of 46 x 46mm and external frame should be of 46 x 52mm. Section for glass beading should be of 18 x 25mm and centre mullion should be of 46 x 70mm. Fixing details: The frame and shutter sections should be cut to length and mitre joined with corner bracket made of CRCA electro plated. Mullion section should be joined with frame / mullion using nylon mullion cap. Ethyl Propylene Diamine Monomer (EPD) Gasket should be used all around glass in shutter between frame and glazed shutter and both sides of fixed glass
Accessories: Handle made of high grade aluminium powder coated and with nylon receiver. Gaskets made of Ethyl Propylene Diamine Monomer (EPDM). Corner brackets made of CRCA with zinc phosphating. Mullion caps made of glass filled nylon.
Glass: Glass shutter and fixing glass portion should be provided with a glass of 5mm plain float glass.
"Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4"" intervals. Total grill unit should be power coated and fixed to window frame with screws.
The above frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames."
sqm. 5350.00
237 Pre-painted Galvanized Iron Windows (Semi Air Tight Model) with Grill and Glass: Providing and fixing Eco 3000 Series Window fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.5 8mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: Sections for frame should be of 48 x 50mm, section for glazed shutter frame should be 47 x 20mm and section for fixed glass bead should be of 12 x 12mm.
Fixing details: The frame and shutter frame sections should be cut to length and mitre joined with polypropylene corner bracket. Mullion section should be joined with frame / mullion using nylon mullion cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter
Accessories: Each glazed shutter should be provided with SS pivot hinges - 1 set, Polypropylene handle - 1 No. with receiver and aluminium peg stay powder coated - 1 No. 
Glass: Glass shutter and fixing glass portion should be provided with a glass of 4mm Pinhead Glass.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4" intervals. Total grill unit should be power coated and fixed to window frame with screws.
Window Frame should be fixed to brick masonry / concrete masonry by using Nylon self-expanding caps and driving MS electr oplated 80mm long screws into the caps through frames.
sqm. 5000.00
238 "Pre-painted Galvanized Iron Windows (Semi Air Tight Model) with Grill and Glass: Providing and fixing Eco 3000 Series Window fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.5 8mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: Sections for frame should be of 48 x 50mm, section for glazed shutter frame should be 47 x 20mm and section for fixed glass bead should be of 12 x 12mm.
Fixing details: The frame and shutter frame sections should be cut to length and mitre joined with polypropylene corner bracket. Mullion section should be joined with frame / mullion using nylon mullion cap. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter
Accessories: Each glazed shutter should be provided with SS pivot hinges - 1 set, Polypropylene handle - 1 No. with receiver and aluminium peg stay powder coated - 1 No. 
Glass: Glass shutter and fixing glass portion should be provided with a glass of 4mm Pinhead Glass.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 12mm x 5mm flat at 4"" intervals. Total grill unit should be power coated and fixed to window frame with screws.
Window Frame should be fixed to brick masonry / concrete masonry by using Nylon self-expanding caps and driving MS electr oplated 80mm long screws into the caps through frames."
Pre-Painted Galvanized Iron Windows with Glass, Grill & Fly Mesh:
Providing and fixing Windows from roll formed
sections made of galvanized steel powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint specification: Coated sections should be with
primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: Section for frame should be of 72mm x 55mm, section for mullion should be of 72mm x 50mm, section for shutter frame should be of 47mm x 20mm, section of fixed glass bead should be of 12mm x 12mm and section for fly mesh shutter frame should be of 40mm x 20mm.
Fixing details: Section for frame, glazed shutters and mesh shutters should be cut to length and mitre joined with polypropylene corner brackets, mullion section should be joined with frame / mullion using mullion
cap.. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass in shutter and fixed glass. Spoon profile should be used around Fly mesh to fix mesh in mesh shutter.
Accessories : Each glazed shutter and mesh shutter
should be provided with SS pivot hinges - 1 set,
Polypropylene handle - 1 No. with receiver and aluminium powder coated peg stay - 1 No. for glazed Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass.
Mesh: Mesh shutter should be provided with a SS 32 gauge fly mesh of 304 grades with 144 holes per square inch.
Grill: Windows should be provided with grill made of 10mm square MS bars welded to 5mm x 12mm flat at 4" intervals. Total grill unit should be powder coated and fixed to window frame with screws.
Window frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.
sqm. 6600.00
239 Pre-Painted Galvanized Iron Two Track Sliding Window: Providing and fixing pre-painted two track, two panel sliding system fabricated from roll formed sections made of galvanized steel powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm. Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns.
Dimensions of sections: Section for frame two track
should be of 59mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm.
Fixing details: The frame and shutter sections should be cut to length, joined with corner brackets made of glass filled nylon. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass.
Accessories: Corner brackets made of glass filled nylon
gasket made of Ethyl Propylene Diamine Monomer
(EPDM). Locking system should be of single pin locking for Windows. Single wheel rollers for windows should be provided.
Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass.
Window frame should be fixed to brick / concrete
masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.
sqm. 4800.00
240 Pre-Painted Galvanized Iron Three Track Sliding Windows: Providing and fixing pre-painted three track, three panel sliding system fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 'D' quality, galvanized as per. IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint specification: Coated sections should be with primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns.
Dimensions of sections: Section for outer frame three track should be of 92mm x 44mm, section for shutter should be of 35mm x 49mm for window, section for euro groove should be of 25mm x 24mm and for lap strip should be 30mm x 41mm. Fixing details: The frame and shutter sections should be cut to length, joined with corner brackets made of glass filled nylon. Ethyl Propylene Diamine Monomer (EPDM) Gasket should be used all around glass.
Accessories: Corner brackets made of glass filled nylon.
Gasket made of Ethyl Propylene Diamine Monomer (EPDM). Locking system should be of single pin locking for windows. Single wheel rollers for windows should be provided.
Glass: Glass shutter and fixed glass portion should be provided with a glass of 4mm pinhead glass.
Window frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.
sqm. 5300.00
241 Pre-Painted Galvanized Iron Fixed Louvered
Ventilators with Glass and Grill:
Providing and fixing louvered ventilator fabricated
from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.58mm.
Paint specification: Coated sections should be with
primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: The section for external frame should be of 57mm x 33mm.
Fixing details: The section should be cut to length, joined with profile to profile component.
Accessories: Glass holding flanges made of glass filled nylon.
Glass: Louvers should be provided with 4mm pinhead glass.
Grill: Ventilator should be provided with grill made of 10mm Square MS bars to 12mm x 5mm flat at 4" intervals. Total grill unit should be powder coated and fixed to ventilator frame with screws.
The above frames should be fixed to brick / concrete masonry walls and floor by means of self-expanding screws.
sqm. 4800.00
242 Pre-Painted Galvanized Iron Door Frame:
Providing and fixing door frames from sections made of galvanized steel powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 217 with zinc of 120 grams / sqm.). The factory made section should be with a powder coating of pure polyester powder of 50-60 microns thick with total coated
thickness of 1.25mm. Size of door frame section should be of 105 x 60mm with a rebate of 37mm to accommodate 35mm thick door shutter. The frame section should have groove to insert gasket. 2 tie rods of 10mm for steel to be provided at bottom. Provision for aldrop, mortise lock to be made in the section as per the instruction of Engineer-in-Charge. The frame section should be cut to length, and joined by way of welding.
Note: 1.25mm thick (Total coated thickness tolerance as per IS 513)
Rm 580.00
243 Pre-Painted Galvanized Iron windows (Air Tight
Model) with Acrylic Sheet & Grill:
Providing and fixing Ajanta Cave Model window
fabricated from roll formed sections made of galvanized steel colour coated / powder coated (Base steel as per IS 513 'D' quality, galvanized as per IS 277 with zinc of 120 grams / sqm.) with total coated thickness of 0.6mm.
Paint specification: Coated sections should be with
primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns. Dimensions of sections: Sections for shutter should be of 46 x 46mm and external frame should be of 46 x 52mm. Section for glass beading should be of 18 x
25mm and centre mullion should be of 46 x 70mm. Fixing details: The frame and shutter sections should be cut to length and mitre joined with corner bracket made of CRCA electro plated. Mullion section should be joined with frame / mullion using nylon mullion cap.
Ethyl Propylene Diamine Monomer (EPDM) Gasket
should be used all around glass in shutter, between frame and glazed shutter and both sides of fixed glass
Accessories: Handle made of high grade Aluminium
Powder coated and with nylon receiver. Gaskets made of Ethyl Propylene Diamine Monomer (EPDM). Corner brackets made of CRCA with zinc phosphating. Mullion caps made of glass filled nylon.
Glass: Glass shutter and fixing glass portions should be provided with a glass of 6mm acrylic sheet.
Grill: Windows should be provided with grill made of
10mm square MS bars welded to 12mm x 5mm flat at
4" intervals. Total grill unit should be powder coated
and fixed to window frame with rivet. The above
frame should be fixed to brick / concrete masonry by using nylon self-expanding caps and driving MS electro plated 80mm long screws into the caps through frames.
sqm. 5700.00
244 Structural Glazing:
Providing and fixing structural glazing fabricated from roll formed sections made of galvanized steel colour coated (Base steel as per IS 513 of 'D' quality, galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.72mm. The glass holding section made of 304 grade SS of 0.6mm thick. Galvanized steel sections are to be used as
stiffeners inside the colour coated steel / powder coated sections as per the design requirement. Design calculations are made to suit wind pressures as given in IS 875.
Paint specifications: Primer coat with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder upto 50-60 microns thick.
Dimensions: The section should be of 37 x 53mm for frame vertical, 37 x 53mm for frame horizontal section and section for reinforcement should be of 31 x 55mm. glass holding section should be of 37 x 37mm for top and bottom grids in between should be of 37 x
18mm
Accessories: Brackets made of CRCA powder coated / electro plated should be used to fix vertical at top and bottom and vertical to slab as per site requirement. Polyurethane brackets should be used to connect horizontal section to vertical sections.
Silicone: Natural cure, with good UV resistance to be used.
The above frame should be fixed to brick / concrete masonry by using nylon self-expanding cap and driving MS electro plated 80mm long screws into the caps through frames.
Glass: 5mm reflective Saint Gobain OR equivalent.
sqm. 5700.00
245 Pre-painted Galvanized Iron Fixed Louvered
Ventilators with Glass, Mesh and Grill:
Providing and fixing louvered ventilator fabricated
from roll formed sections made of galvanized steel colour coated / powder coated (Base Steel as per IS 513 of 'D' quality, Galvanized as per IS 277 with Zinc of 120 grams / sqm.) with total coated thickness of 0.58 mm
Paint specification: Coated sections should be with
primer coat of epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and black coated with alkyd backer of 5-7 microns. Dimensions of section: The section for external frame should be of 57 x 33mm.
Fixing details: The section should be cut to length and joined with profile to profile component.
Accessories: Glass holding flanges made of glass filled nylon.
Glass: Louvers should be provided with 4 mm thick
pinhead glass.
Mesh: Mesh should be provided with a SS 32 gauge fly mesh of 304 grades with 144 holes per square Inch. Grill: Ventilator should be provided with grill made of 10mm square MS bars welded tol2mm x 5mm flat at 4" intervals. Total grill unit should be powder coated
and fixed to window frame with screws.
The above frames should be fixed to concrete /
masonry walls and floor by means of self expanding screws.
sqm. 5100.00
246 Providing UPVC (Un-Plasticized Polyvinyl Chloride)
Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have
dimensional stability. The sash should be of 60 x
102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.
Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.
Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam
Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.
sqm. 7000.00
247 UPVC Window
Specification:
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)
Windows of casement type (open) from the profile the size
of outer frame 60mm x 58mm and shutter profile are
reinforcement with GI/lmm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be
provided with Espag multi power point locks and also it
operates as handle. The corners and joints should be welded
and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security
protective hinges, strong locking systems and as per size for
arresting noise and energy loss. The connecting mechanism
between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work
sqm. 6300.00
248 UPVC Window
Specification:
Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride)
Windows of casement type (open) from the profile the size
of outer frame 60mm x 58mm and shutter profile are
reinforcement with GI/lmm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be
provided with Espag multi power point locks and also it
operates as handle. The corners and joints should be welded
and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security
protective hinges, strong locking systems and as per size for
arresting noise and energy loss. The connecting mechanism
between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work
sqm. 6825.00
249 ABS DOOR / EQUIVALENT
Specification:
Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work
RM 447.00
250 ABS DOOR / EQUIVALENT
Specification:
Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm - 2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges - 3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work
   
a Plain Pre-laminated Door sqm. 5775.00
b Design Pre-laminated Door sqm. 6090.00
  New Items    
251 Autoclaved Cellular Aerated Concrete Blocks    
a 600mm x 200mm x 100mm Each 44.50
b 600mm x 200mm x 150mm Each 66.75
c 600mm x 200mm x 200mm Each 89.00
d 600mm x 200mm x 225mm Each 100.50
e Self Curing AAC Joint Mortar 40 Kg/Ban 595.00
f Ready Mix Plaster for Rendering 50 Kg/Baa 295.00
252 Aerated Auto Claved Cellular Concrete Block 60cm x 20cm x 10-30cm Each Deleted
253 Plasticizer / Super Plasticizer Kg. 42.00
254 Making through holes in Plain or Reinforced Cement
Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete - Depth per cm
   
a 100mm Each 315.00
b 150mm Each 420.00
c 200mm Each 472.00
255 Supplying and Installing Metal False Ceiling using Fire
Retardant Galvanized Steel Sheet Plain lay in tile size 600mm x 600mm, 0.5mm thick, powder coated on external surface and shall have flange on all four sides to rest on the exposed grids. The system to give 600mm x 600mm centre to centre rr. The 'T' shall be not be dipped GI Tee Section 3600mm long main Tee. 24mm wide and cross Tee panels are formed by running main runner of 'T' section of size 30mm x 24mm powder coated at bottom at intervals with powder coating at
bottom. Necessary provision of inter locking of 'T section
are made at required intervals not exceeding 1200mm. The
main runners are suspended from the ceiling by means of 4mm dia. GI rods fixed to the ceiling using anchor fasteners of 50mm x 8mm size with nylon inset and hooked to the main rubbers using clips. The last hangers at end of each rubber should not be greater than 600mm from the adjacent wall. The last panel shall be placed at the side wall using edge profile 'L' Angle of size 20mm x 20mm and fixed to the side wall the false ceiling should be fixed of same level and should present a neat look
sqm. 3060.00
  New Items    
256 Supplying and fixing of SS Wall Cladding sqm. 12500.00
257 Supplying and fixing of SS False Ceiling sqm. 7500.00
258 Supplying and Fixing of Aluminium Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes    
a Aluminium Dye Cast Letters 9" size Each 1040.00
b Aluminium Dye Cast Letters 6" size Each 660.00
259 Providing Wall Panelling using one side teak wood
sheet with melamine polishing with following
specification. The frame using aluminium tubular section of size 50mm x 25mm x 2mm thick fixing horizontally and vertically in position with wall at interval of 0.60m in both diretions, fixing water proof plywood of 12mm thick over the aluminium frame work with necessary screws. One side teak wood sheet of 3.5mm thick will be fixed over the plywood using fevical and finishing with melamine polishing and the rate inclusive of conveyance to site and labour charges and as directed by the Departmental Officers. The design pattern, water proof plywood, OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work etc., complete.
sqm. 5668.00
260 Providing and fixing Acoustic Wall Panelling
(equivalent to Armstrong) in channelled wood works perforated panels of width 192mm, thickness of 15mm and length of 2400mm or as per required by the Departmental Engineer made of a high density fibre board with minimum 725 kg./m3 density substrate with a laminated facing as per the approved shade and finish and a melamine balancing layer on the reverse side. The boards shall have a special peforation pattern where the visible surface has a "Helmholtz" fluted perforation of 3mm width and 21mm of visible panel each. The edges of the panels shall be "tongue­and-grooved" to receive special clips for installation. The back of the perforated panel shall have sound absorbing non woven acoustical fleese having NRC of 0.52. The panels shall be mounted on special aluminium splines using clips provided by Armstrong and approved by the Engineer-in-Charge
Installation: Install aluminium box section (provided by others) of section 50mm x 25mm or as approved by the Engineer-in-Charge on the solid wall horizontally using screws and plugs at spacing of 600mm centre to centre. Screw the aluminium extruded keel for channelled wood works provided by Armstrong over the lowest and second aluminium section at an on centre distance of 600mm. Place the inside clip on the groove end of the panel along the aluminium keel and then place the tongue end of the next panel. Continue installing rows of panels by inserting the tongue into groove of the earlier inserted panel and progressively installing inside clips into the next keel till the actual height is achieved. Finish off the edges using wooden
moulding of matching colour (provided by others). Installation to be carried out by Armstrong Trained Installation Team and installation should be carried out as per Armstrong Recommended Procedure.
sqm. 8046.00
261 Supplying and fixing the Wall Panelling with the
following specification fixing horizontally and
vertically in position of wall. Fixing the water proof ply wood 9mm thick board over the country wood planks. Over the ply wood OST sheet of 4mm thick will be fixed with necessary screws and fevicol giving neat finsih. The top will be finished with two coats of sanding polishing. The surface will be finished with necessary design as directed by the Departmental Officers. The rate inclusive of all materials, labour power and conveyance of materials to the work site, loading & unloading etc., and as per drawing and design by the Departmetnal Officers. The water proof ply wood and OST sheet and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.
sqm. 5250.00
262 Providing and fixing of 1.2mm thick Lead Lining Door for X- Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer sqm. 13650.00
263 Post Tensioning Work: MT
Design and execution of post tensioning work, including
decoiling, the strands, cutting to the required lengths,
supplying, laying of HT strands sheathing (GI corrugated ducts 0.3mm thick) jointing with couplers and inserting the strands, profiling, fixing liveend anchorages, including supply of stressing anchorages, suitable for 5-5 & 5-4 tendons,
grout vents, making dead end anchorages, including flowering the strands, fixing tendon support bars, supervising the fixing of antibursting reinforcement, stressing the cables, end trimming, grouting the cables, with cement slurry, mixed with admixtures with required tools, plants, and machineries, and consumables etc. (Shuttering, concreting & reinforcement steel shall be paid under respective items) at all heights including all leads, lifts, coordination, with the post- tensioning agency, preparation of drawings, obtaining approval from the Employer / Architect etc. Rate to include providing water, power, cement and admixture for grouting, packing of sheathing and anchorages blockings, filling of recess pockets after stressing using grouts (cement slurry mixed with approved admixtures) including providing access to post tensioning at all heights including all leads, lifts etc., all complete and as approved and as directed by the
Employer Architect but excluding shuttering, concreting & reinforcement steel which shall be payable under respective items separately.
MT 194000.00
264 Supplying, fabricating and fixing in position factory
made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor spring for each shutter, concealed tower bolt, suitable stainless steel locking arrangement and other
necessary furniture fittings of approved quality. The
vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers
Sqm. 36700.00
265 Brass Letters    
a 25cm (10") Each 892.00
b 37cm (15") Each 1260.00
c Emblem (15") Each 12600.00
266 Manhole Cover SFRC    
a 600mm x 600mm Each 2625.00
b 750mm x 750mm Each 2885.00
c 900mm x 900mm Each 3150.00
267 Incinerator for Ladies Bathroom (For School Works) Each 33600.00
268 Polycarbonate Sheet 6mm thick Sqm. 630.00
269 Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum­Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories.
(a) MS Skid - 1 No.
(b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set
(c) Feed Pump 0.50 HP - 1 No. .
(d) Vertical Pump 2-9, 2.00 HP / Single Phase - 1 No.
(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.
(f)  Flow Meter - 1 No. 20" Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. .
The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of
all civil works, wherever necessary to install the System in position and intact.
   
  New Item    
a 50 Litres Set 39150.00
b 250 Litres Set 105000.00
c 500 Litres Set 220000.00
d 1000 Litres Set 367000.00
e 2000 Litres Set 504000.00
  New Items    
  Medical Gas Arrangements    
270 Medical Gas Copper Pipeline arrangement to hang on
the wall of socket type connection installation of
seamless cleaned and degreased non arsenical
phosphorous gas copper pipe line with saddles
complete with brazing work including all copper fitting
(tee, elbow, reducer, coupling). The copper pipelines
should be tested suitable for a steam of working pressure of 17.34 kg. / cm2 (17 bar) and confirm to BS 864 Standard with specially made for brazed socket type connection. The medical gas copper pipeline should be tested as per standard and commissioning after painting as per International Code No. IS
2379/1963 Table-V. The pipelines installed at the various wings and floors etc., complete as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.
   
a 10mm OD 0.90mm thick copper pipe RM 308.00
b 15mm OD 0.90mm Thick Copper Pipe RM 448.00
c 22mm OD 0.90mm Thick Copper Pipe RM 748.00
d 28mm OD 0.90mm Thick Copper Pipe RM 924.00
e 42mm OD 1.20mm Thick Copper Pipe RM 2000.00
f 54mm OD 1.20mm Thick Copper Pipe RM 2500.00
271 Gas Outlet Points: (Self sealing type - Single / DIN outlet pipe) with 'S' type bracket made up of copper and the out let of non-interchangeable for other gas. The outlet points are brazed with brass bracket with self sealing valve (Stainless Steel) with all accessories and complete set and are covered by plastic cover duly colour coated as per specific gas and button cover etc., complete as directed by the Departmental Officers and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification. Each 1144.00
272 Oxygen manifold arrangements of 2 banks x 12 cylinder each wing with semi automatic control panel which includes contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IO x regulator 2 Nos. with suitable adopter, flexible SS Hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordance with IS 1282-1989. Emergency alarms with illuminating display for low / high pipeline pressure and malfunctioning of system. 1) Mainfold top frame with provision for connecting 12 cylinders on right bank and 12 cylinders on left bank with high pressure interconnecting copper tubing, silver brazing, non return valve, fasteners and cylinder spport middle angle frame for claping 2 x 12 cylinders and related fasteners. The 02 manifold should with stand a pressure of 140 kg. / CM2. The installation is commissioned after testing as per standards and painted as per International Code and as directed by the Departmental Officers as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification. Each 162800.00
273 Nitrous Oxide Manifold Arrangements of 2 banks x 3 cylinder
each wing, with automatic control panel which includes
contact gauge 2 Nos., outlet pressure gauge, brass heavy duty IOX regulator 2 Nos. with suitable adopter, flexible SS hose. Mainfold shall be of a construction and of a designs and material suitable for the service pressure in accordante with IS 1282-1989. Emergency alarams with illuminating display
for low / high pipeline pressure and malfunctioning of
system.
1)   2 x 3 cylinder Nitrus Oxide Manifold should be suitable
with stand a pressure of 140 Kg. / Cm2 and above along with high pressure copper annealed tail pipes with end brass
adapter suitable for Nitrous Oxide Cylinders and manifold.
2)   Top frame comprising of high pressure copper pipes of size 12mm ID 1.5mm wall thick with high pressure brass
fittings made of high tensile brass and connections through non-return valves, high pressure copper tail pipes made of high pressure copper pipe size of 7mm ID x 1.5mm thick.
3)   The design of middle and bottom frames should be
provided to fit both round and flat bottom cylinders safely with fitted heavy duty regulator. The Manifold should be
tested at 3500 pig as per IS 12827 / 1989 & ISO 7396 / 1987 Specification.
Each 92400.00
274 Brass Isolation Valve suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball valve of reputed make, conneced in line with medical gas pipe line system by using suitable size brass valve adopter union, ferrule, nipple, rubber "01 ring, tapion
lap and etc. All pipe line regulators shall be capable of
controlling pipe line pressure and must compatible with
the requirements specified in IS 12827-1989. All
valves should be pneumatically tested for twice the working pressure for the gas line as per IS Code 12827 / 1989 & ISO 7396 / 1987 Sepecification.
   
a 15mm Isolation Valve Each 1188.00
b 22mm Isolation Valve Each 1804.00
c 28mm Isolation Valve Each 2068.00
d 42mm Isolation Valve Each 3800.00
275 Theatre Vaccum Unit: The unit should comprise of two reusable 2000 ml shatter resistant bottle. Each made up of ply carbonate material and fully autoclavable at 134 degreee centigrade, should have a vacuum regulator with instant ON / OFF switch and tree way left, right or both. All the above items should be
mounted on a trolley having free moving castor
wheels. (As per IS 12827 / 19898 & ISO 7396 / 1987)
Each 10500.00
276 Flow Meter made up of Brass with Humidifier Bottle
Flow Meter should be back pressure compressed and
should be accurate gas flow measurement with control
range 0-13 litres per minute. It should meet strict
permission and dumbling standard. The meter body
should be made of brass materials. The humidifier bottle should be made of unbreakable polycorbonate material and auto cleavable at 134 degree centigrate: The rate includes flow meter and its accessories (silicon tube with mask). The cost of materials including transport, etc., complete as per standard specification and as directed by the Departmental Officer and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification.
Each 1337.00
277 Ward Vaccum Unit with Gauge both mounted on a
collection jar of capacity 600 ml and with a wall
bracket for mounting it on the wall. The collecion jar
should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degree centigrade as per standard specification and as directed by the Departmental Officers and as per IS 12827 / 1989 and ISO 7396 / 1987 Specification. The
rate includes cost of silicon hose with SS nipple on
either side.
Each 1600.00
278 Supply, installation, testing and commissioning of equivalent to Ingersoll Rand Reciprocating Air Cooled Type (10 HP + 5 HP) rating Vaccum Pump as per following provisions.
As per IS 12827 / 1987 & ISO 7396 / 1987 Specification
a)  Vaccum pump - 10 HP - 1 set
b)  Electric motor - 5 HP -1 No.
c)  DOL Starter with OLR - 1 No.
d)  Vaccum switch - 1 No.
e)  Vaccum Gauge - 1 No.
f)  Control Frame with Fittings - 1 No.
g)  Suction Scrubber -1 No.
h)  V-Belts - 1 No.
i)  GI & MS Fittings - 1 No.
j)  Brass Fittings - 1 No.
k)  Exhaust Silencer - 1 No.
i) Base frame for motor and vaccum pump - 1 set
m) Pilot line with fittings - 1 set, Vaccum Room &
Air Compressor Room Inside
Each 395000.00
279 Supply, installation, testing and commissioning of
Compressed Air System of Reciprocating Oil Free Air Compressor belt driven type air compressor with following provisions.
As per IS 12827 / 1987 & ISO 7396 / 1987
Specification
Compressor package consists of following:
a) 10 HP Air Compressor - 2 Nos.
b) Electric Motor 10 HP-1 No.
c)  Dol Starter - L&T-10 HP - 1 No.
d) Base Frame Kit (for Motor and Compressor) - iset
e) Pressure Swith - 1 No.
f)  Pressure Gauge - 1 No.
g) NRV and Pilot Fittings - 1 No.
h) Delivery Tube - 1 No
i) Foundation Bolts & Anchor Fasteners - 1 Lot
j)  Belt Guard - 1 No.
k) Air Drier 50 to 60 cfm. capacity - 1 No. Drain Ball
Valve - 1 No., Air Outlet Ball valve - 1 No.,
Vacuum Room & Air Compressor Room Inside
Accessories:
Non-Return Valves, Air Pressure Switch, Pressure
Gauge, Isolation Valves, Air Filters etc.,
Inter connecting piping: Mild Steel Pipe of 2" with
fittings.
Each 415000.00
280 Supply, installation, testing and commissioning of MS Fabricated Vertical Mounted Type 1000 liters capacity Vaccum Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump, etc., as directed by the Departmental Officers. Each 85800.00
281 Supply, installation, testing and commissioning of MS Fabricated Vertical Mounted Type 1000 liters capacity Compressed Air Receiver with inlet and outlet and drain holes provided suitable to operate with vaccum pump etc as directed by the Departmental Officers. Each 85800.00
282 Single Arm Pendent Mounted on Celing Height as
directed by the Departmental Officers. All items are
MS powder coated. The cost includes cost of all
materials, labour charges, dismantling and re-doing
masonry to original condition, painting of masonry
works taxes including transports, risk allowance, scaffolding etc., complete and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specification.
Each 142000.00
283 Bed Head Panel of size 1m, length, height 0-0.30 cm and depth of 4". The aluminium powder coated with requirement colour for provision points of 02-2 Nos., Air 1 No., Vaccum 1 No. with double electrical socket with switch 2 Nos. with 2 set with 1V - bottle holder fixing to the wall hanging including monitor stand etc., complete. Each 16000.00
284 Supplying, fabricating and fixing slotted carriers with
the following specifications. The carriers should be
made of GI sheet of 16G with slots. The size of carrier
is 300 x 40mm and are to be spaced at 50 cm centre
to centre. The carriers are to be fixed on suspenders
with the help of lock nuts. These suspenders are made
of galvanised MS rods size of 6mm dia. The
suspenders should be threaded to its full length so that
the carrier shall be fixed at any height depending on
the onsite requirement. The suspenders are to be fixed
on the soffit of ceiling with self fixing anchore bolts. All
components of suspenders and slotted carriers should
be galvanised. The rate includes cost of all materials,
labour charges for drilling and fixing the whole assembly at required places, complete and as directed by the Departmental Officers.
Each 145.00
285 Supplying and fixing of Cylinder 46 Litre "D" Type
Empty Seamless Medical Nitrous Cylinder with Valve and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specifiaton etc., complete and complying with standard specification.
Each 14120.00
286 Supplying and fixing of Cylinder 46 Litre "D" Type
Empty Seamless Medical Oxygen Cylinder with Valve and as per IS Code 12827 / 1989 & ISO 7396 / 1987 Specifiaton etc. complete and complying with standard specification.
Each 14120.00
287 Supplying, fabricating and fixing Oxygen Boyles Kit for Operation Theatre with following specification: The Boyles Kit Hose is made of silicon and of white colour as per standard suitable adoptor fixed on higher end of hose to connect outlet unit and Boyles Machine. The
adopter must be made of SS of superior quality. The
rate includes cost of all materials and labour charges for fixing in proper position etc. complete and complying with standard specification.
Each 1600.00
288 Supplying, fabricating and fixing Nitrous Oxide Boyles Kit for Operation Theatre with following specification: The Boyles Kit Hose is made of silicon and of white colour as per standard suitable adoptor fixed on higher end of hose to connect outlet unit and Boyles Machine. The adopter must be made of SS of superior quality. The rate includes cost of all materials and labour charges for fixing in proper position etc. complete and complying with standard specification. Each 1600.00
  FIRE FIGHTING ARRANGEMENTS    
289 Wrapping and Coating Anti-Corrosive Treatment for under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers.    
a 100mm dia RM 350.00
b 80mm dia RM 250.00
290 Supply, erection, testing and commissioning of 80mm dia Heavy Duty Foot Valve including necessary MS flange of table 'E', gaskets, bolts & nuts, etc., installed at end of 80mm dia suction pipeline at sump as per the standard method and as directed by the Departmental Officers. Each 13000.00
291 Supply, erection, testing and commissioning of cast iron body and gun metal or stainless steel Internal Non. Return Valve of size of 80mm dia to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table 'E', gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Each 10500.00
292 Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and re­doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: POLYCAB / PARACON /
FINOLEX / EQUIVALENT.
   
a 3 core 95 sq.mm. armoured aluminium cable RM 500.00
b 4 core 16 sq.mm. armoured aluminium cable RM 215.00
c 4 core 10 sq.mm. armoured aluminium cable RM 175.00
d 2 core 1.5 sq.mm armoured multi strand aluminium cable RM 135.00
e 3 core 10 sq.mm. armoured aluminium cable RM -175.00
f 10 core 2.5 sq.mm. armoured aluminium cable . RM 395.00
g 2 core 2.5 sq.mm. armoured aluminium cable RM 155.00
293 Supply, installation, testing and commissioning of
Micro Processor based Conventional 12 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt, 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.
Each 77000.00
294 Supply, installation, testing and commissioning of Micro Processor based conventional 4 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. Each 45000.00
295 Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers. (Make: Apollo / Equivalent) Each 2100.00
296 Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent) Mtr 1600.00
297 Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers (Make: Ravel / Equivalent) Each 1550.00
298 Supply and laying of FRLS PVC insulated 2 core 1.5
sq.mm. Armoured Copper Cable on ceiling / wall using
fixing accessories like screws, plug, clamps, etc., as
per standard methods and as directed by the
Departmental Officers.
Each 100.00
299 Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, wall mounting bracket, safety clip, etc., as directed by the Departmental Officers. Each 6000.00
300 Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 700mm with following specification:
a. Door Frame 1.6mm: Galvanized 120 GSM branded make JSW
b. Door Leaf 1mm: Galvanized 120 GSM branded make JSW
c. Shutter Thickness: 46mm
d. Honeycomb: In-fill
e. Glue Macroplast UR-7221
f.  Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS 304 - Finish SS
g. Door Closer with Standard Arm Finish: Silver
h. Lock Set: Dead Lock with both side key
i.  Door Orientation: To be confirmed by client
j.  Mounting of door: Brick wall mounted
k. Powder Coating: Powder coated in standard RAL paint
colour of PO Red (60 to 90) Microns
I. Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent
m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent
n. Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame
o. Rated Glass Schott Pyran with Frame
p. Anchor Bolt with Endcaps
The above assembly mounted on concrete or brick wall
including the cost of cutting, chipping, concrete packing, pastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.
Each 73000.00
301 Supply, erection, testing and commissioning of fire fighting application Monoblock Motor Pumpset of 1100 LPM at 45 metres head to develop 3.5 kg / sq.cm at the highest and farthest hydrant point to make 30m water jet at the time of fire fighting emergency cicumstances, coupled with 15 KW / 20 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast iron body, bronze impeller, rope gland packaging, suction size of 100 mm dia, delivery size of 80 mm dia, including the cost of foundaton concrete, anti-vibration mounting, rain safety hood and etc.,
complete as directed by the Departmental Officers
(Make: Kirloskar KDS 2050+ or Equivalent)
Each 219000.00
302 Supply, erection, testing and commissioning of fire
fighting application monoblock motor pumpset of 900
LPM at 40 metres head to develop 3.5 kg/sq.cm at the
heightest and farthest hydrant point to make 30 m
water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete
anti vibration mounting, rain safety hood and etc.
complete as directed by the Departmental Officers
(Kirloskar make KDS 1555+ or Equivalent)
Each 133000.00
303 Supply, errection, testing and commissioning of Fire
Fighting Electrical Control Panel of 15 HP, 415 V, 50 Hz
Rating Wall Mounted Type fabricated using CRCA
sheet, hinged lockable door, dust and vermin proof
with following provisions:
a.  63 Amps, 4 Pole MCB - Incomer, 6 Amps, 2 Pole MCB for Control Circuit - 1 set
b.  R, Y, B Phase Indication Lamp, Volt Meter (0 - 500 V), Ammeter (0 - 50 A), Volt Meter Selector Switch- 1 set
c.  32 Amps Power Contactor with 230 V Coil, 14 - 23
Amps Over Load Relay - 1 set
d.  Single Phase Preventer - 1 No.
e.  Indication Lamp for Motor ON / OFF / TRIP - 1 set
f.   AUTO / MANUAL Selector Switch, ON / OFF Push Button - 1 set
g.  Add On Block, Terminal Block, Power Wiring, Control Wiring, Connectors, Cable Lugs, Slotted Cable Cover The above panel mounted on wall using anchor fasteners bolts, plugs, incoming and outgoing cable connection and all works carried out as per standard methods and as directed by the Departmental Officers.
Each 78500.00
304 Supply, erection, testing and commissioning of Fire Fighting
Application Horizontal Centrifugal Type Pump Rated for 2280
LPM at 70 metres head with Electrical Motor of 60 HP of 415
volt 3 phase connection complete with base plate and
accessories. (Make: Kirloskar or Equivalent). The rate
inclusive of necessary vibration, bad mounting etc., as per
standard method as directed by the Deparmental Officers.
Each 405000.00
305 Supply, installation, testing and commissioning of Diesel
Engine Driven Main Fire Pump suitable for automatic
operation and consisting of following and complete in all
respects as required.
a.   End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520.
b.   68 BHP, 1500 RPM water cooled with radiator, diesel
engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc.
c.   110 .litres capacity diesel tank mounted over stand
fabricated using 25mm x 25mm x 6mm size MS angle,
providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent).
d.   Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto lm, outside pump house duly insulated with 50mm thick glass wool with imm thick
aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition
e.   Dash board consisting the instruments like temperature
gauge, galvano type DC Ammeter, lubricant oil pressure
gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required.
f.   12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required.
g.   Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration
mounting arrangement.
All works carried out as per standard methods and as
instructed by the manufacturer and as directed by the
Departmental Officers. (Make: Kirloskar / Equivalent)
Each 1085000.00
306 Supply, erection, testing and commissioning Mono
Block type Fire Fighting Pressurisation Pump of 180
LPM 110 metres head at 10 HP with suitable base
frame including necessary vibration bad mounting etc.,
including conveying, fixing and incidental charges.,
etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)
Each 198000.00
307 Supply, erection, testing and commissioning of Fire
Fighting 2 Way Fire Brigade Inlet with necessary gun
metal 63mm die non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition
wherever found neccessary., etc., complete as per
standard specification and as directed by the
Departmental Officers. (Make: KIARTAR / OMEX /
EQUIVALENT)
Each 12000.00
308 Supplying, erection, testing and commissioning of
Diesel Engine Pump Main Control Panel & Jockey Pump
including necessary auto cut-in, cut-off and manual
operations, battery charger switch arrangements,
voltmeter, ammeter and running indication siren provision, wall mounting type, etc., as per the standard method and as directed by the Departmental Officers.
Each 115000.00
309 Supply and laying of 4 core 10 sq.mm. armoured
copper cable for power wiring to the Terrace Pump
Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers.
RM 555.00
310 Supply and laying of 2 core 1.5 sq.mm. armoured copper cable for control wiring to the Terrace Pump Motor with runs of 14 SWG TC wire for earthing, providing in wall with suitable size GI clamps, screws, wooden plug, end termination by using suitable size cable glands, copper sockets and etc., as directed by the Departmental Officers. RM 135.00
311 Supply, erection, testing and commissioning of Fire
Fighting Application direct on line main control panel to
control electrical Terrace Pump Motor of 3.75 KW / 5
HP rated 415 volts / 50 Hz 3 phase, 2880 RPM
including necessary auto / manual operations, over load relay, selector switches arrangements, voltmeter and ammeter provision, etc., as directed by the Departmental Officers.
Each 51500.00
312 Servicing the following sizes cast iron body Sluice
Valves by disconnecting from hydrant line, dismantling, inspecting the internal shutter, replacing valve seating, checking operating lever, lubricating for moving parts, reconnecting with hydrant system as per standard methods and as directed by the Departmental Officers.
   
a 80mm dia Each 1400.00
b 65mm dia Each 1200.00
313 Supply and fixing of Fire fighting application oblique
type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table "E", bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Each 9950.00
314 Supply, installation of Fire Fighting Application 180
degree swinging type, hose reel drum with 20mm dia
braided thermoplastic hose of 30 metres long, so as to
extend to necessary distance by self rolling spindle
wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition
wherever found neccessary., etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: OMEX / KARTAR / LIFE
GUARD / SAFE GUARD / EQUIVALENT.
Each 13420.00
315 Supply, and fixing in position of Fire Fighting
Application Hose of 63mm dia of 15 metres length
binded by copper wire with 63mm dia stainless steel
male and female instantaneous fire fighting special
coupling as per IS 901 as directed by the
Departmental Officers. Near every hydrant points
including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.
Each 8870.00
316 Supply, and fixing in position of Fire Fighting
Application 63mm dia stainless steel short length
Branch Pipe with hexagonal type spray nozzle of 15mm
(or) 20mm jet bore. Near every hydrant points
including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found
neccessary, etc., complete as per standard
specification and as directed by the Departmental
Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE
GUARD / EQUIVALENT.
Each 3280.00
317 Supply of Fire Fighting Application MS Hose Box to
keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found
neccessary, etc., complete as per standard
specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.
Each 7650.00
318 Supply and fixing nominal bore quartized bulb type
sprinkler bulb 68 Deg C fast response pendent type including GI collar for each sprinkler bulb, mounted in MS pipe line using suitable size MS threaded coupling, thread, shellac etc., as per standard methods and including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found
neccessary, etc., complete as per standard
specification and as directed by the Departmental
Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE
GUARD / EQUIVALENT.
Each 450.00
319 Supply, erection, testing and commissioning of
following MS 'C' Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table 'E', elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found
neccessary, etc., complete as per standard
specification and as directed by the Departmental
Officers. Make: JINDAL / EQUIVALENT.
   
a 250mm dia RM 5500.00
b 200mm dia RM 4100.00
c 150mm dia RM 2950.00
d 100mm dia RM 2050.00
e 80mm dia RM 1600.00
f 65mm dia RM 1350.00
g 50mm dia RM 800.00
h 40mm dia RM 600.00
i 25mm dia RM 500.00
320 Wrapping and coating anti-corrosive treatment for the following under ground MS pipe having one coat of anti­corrosive metal primer, one layer of asphalt tar tape wound over the MS Pipe as per standard methods as per standard specifications and as directed by the Departmental Officers.    
a 200mm dia RM 450.00
b 150mm dia RM 400.00
321 Supply, erection, testing and commissioning of
following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table 'E', gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT
   
a 200mm dia Each 31000.00
b 150mm dia Each 24000.00
c 100mm dia Each 15000.00
322 Supply, erection, testing and commissioning of cast
iron body and bronze internal non-rising spindle sluice
valve of sizes at required places to control the flow of
water including necessary MS flange of table 'E',
gaskets, bolts & nuts including conveyance, all
incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition
wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: NORMEX / KARTAR /
EQUIVALENT
   
a 250mm dia Each 58000.00
b 200mm dia Each 37500.00
c 150mm dia Each 22100.00
d 100mm dia Each 14900.00
e 80mm dia Each 11000.00
f 65mm dia Each 8300.00
323 Supply, erection, testing and commissioning of Cast
iron body and Gun metal or stainless steel internal Non•
return valve of following sizes to control one way flow
of water to be installed pump room at delivery line
and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table 'E', gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.
   
a 200mm dia Each 46100.00
b 150 mm dia Each 27000.00
c 100mm dia Each 11200.00
324 Supply, erection, testing and commissioning of Gun
Metal Gate Valve of size 50mm dia size including
necessary MS flange of table 'E', gaskets, bolts & nuts
etc., installed at pump house delivery line for the
purpose of priming water to suction line including
conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.
Each 5050.00
325 Supply, erection, testing and commissioning of Gun
Metal Non-Return Valve of size 50mm dia including
necessary MS flange of table 'E', gaskets, bolts & nuts,
etc., installed at pump house delivery line for the
purpose of priming to suction line so that to control
one way including conveying, fixing and incidental
charges etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.
Each 4900.00
326 Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT Each 9000.00
327 Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers. Each 13500.00
328 Supply and laying of following sizes of Armoured
Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental
Officers. Make: POLYCAB / PARACON / FINOLEX /
EQUIVALENT.
   
a 3 core 185 sq.mm. armoured aluminium cable RM 1500.00
b 3 core 10 sq.mm. armoured copper cable RM 670.00
c 10 core 2.5 sq.mm. armoured copper cable RM 600.00
d 2 core 2.5 sq.mm. armoured copper cable RM 200.00
329 Earthing arrangements with GI Earth Plate including
charcoal and salt with necessary excavation in all soils
and to full depth as may be required and masonry
work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.
Each 6000.00
330 Supply, erection, testing and commissioning of
Pressure Gauge with 0 to 14 kg. range of reputed make
with necessary valve, milling thread MS coupling fixed
at delivery pipe line in pump house to read the
developing pressure including conveyance, all
incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition
wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: H-GURU / ISI MAKE /
EQUIVALENT.
Each 3100.00
331 Supply, erection, testing and commissioning of suitable
Pressure Switch of reputed make line Indfoss or
Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including
conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.
Each 5200.00
332 Supplying, installation, testing and commissioning of Fire
Fighting Electrical Control Panel of cubical construction, floor
mounted type fabricated using CRCA sheet,
compartmentalised with hinged lockable door dust and
vermin proof, cable alley, inter connection having switch gears and accessories mounting and internal wiring, earth terminals, numberings, necessary metering protections and indications complete in all respect suitable for operation on 415volt, 3 phase, 50 Hz AC supply with enclosure protection class IP 54 and mounted with the followings.
A. Common Panel in Fire Pump House
(i). Incomer
a. 1 No. 600A TP & N SDFU with HRC fuses
b.1 set of 600A, 4 bar aluminium bus bar, 415 V, 50 HZ AC supply
c. 1 No. (0-500A) digital ammeter with selector switch & CTs
d.1 No. (0-500V) digital voltmeter with selector switch and control fuses
e.3 Nos. phase indication lamp LED type with toggle
switches with control fuses
(ii). Outgoing
a. Main Fire Pump
400 A TPN SDFU with HRC fuses with sutable HP fully
automatic starter / delta starter with over load protection, digital ammeter with built-in selector switch and suitable CTs, current sensing type single phasing preventer complete with all accessories and internal wiring required for automatic operation, selector switch for auto / manual /OFF operation -1 No
b. Jockey Pump
125 A TPN SDFU with HRC fuses with suitable HP fully
automatic starter / delta starter with over load protection, current sensing type single phasing preventer complete with all accessories and internal wiring required for automatic operation, selector switch for auto / manual operation - 1 No.
c. Diesel Engine Control comprising of:
1. Auto / manual selector switch and 3 attempt starting
device, timers and relays as required, push buttons, start / stop in manual mode.
2. Indication lamp for high / low lubricant oil pressure, high water temperature and engine ON indication.
3. Battery charger suitable for 12V /24V DC with boost and tickle selector switch, 0-15V / 0-30V DC volt meter, 0-20A DC ammeter.
4. All standard relays and accessories for automatic operation of diesel engine.
5. The above combined panel mounted over MS channel
fabricated frame with cement concrete platform, all other connection works carried out as per standard methods and including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers.
Each 525000.00
333 Supply erection testing and commissioning of Electric Motor Driven Fire Pumpset suitable for automatic operation and consisting of following:
a.   1 No. horizontal split casing centrifugal type fire pump
capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel,
b.   1 No. squirrel cage induction motor of 175 HP, 415 Volt, 3 phase 50Hz rating, conforming to IS:325-1978 with class "F"
insulation, totally enclosed, IP 55 for enclosure fan cooled type conforming to relevant protection clause of IS 4691, synchronous speed of 2900 RPM.
c.   Common bed plate fabricated with MS channel / cast iron type for assembling the pump and motor flexible coupling between the pump and the motor with coupling guard for protection - 1 No.
d.   Making cement concrete foundation suitable for the above pumpset including vibration isolation pads as necessary,
foundation bolts, brackets, clamp fixtures, grouting, etc., in accordance with the manufacturer's design and as per
standard methods and including conveying, fixing and
incidental charges, etc., complete as per standard
Specification and as directed by the Departmental Officers.
Each 825000.00
334 Supply, installation, testing and commissioning of Diesel
Engine Driven Main Fire Pump suitable for automatic
operation and consisting of followings and complete in all
respects as required.
a.   1 No. horizontal split casing centrifugal type fire pump
capable of delivering 4550 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of stainless steel.
b.   190 BHP, 1500 RPM water cooled with radiator, diesel
engine conforming to relevant BS & IS standard complete.
c.   Auto starting mechanism, 12 volts / 24 volts electric
starting equipment like self motor, dynamo, solenoid
switches, etc.
d.   110 litres capacity diesel tank mounted over stand
fabricated using 25mm x 25mm x 6mm size MS angle
providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc
e.   Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto lm outside pump house duly insulated with 50mm thick glass wool with 1mm thick
aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition.
f.   Dash board consisting the instruments like Temperature
Gauge, Galvano Type DC Ammeter, Lubricant Oil Pressure Gauge, Ignition Switch, Emergency Stop and all other
protection equipment as per specification, stop soleneid for auto stop in the event of fault with audio indications, painted with Post Office Red Colour, etc., as required.
g.   12V / 24V, storage battery, maintenance free tape, 180AH rating, MS fabricated common base plate, coupling guard,
foundation bolts, etc., as required.
h.   Postioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration
mounting arrangement.
All works including conveying, fixing and incidental charges, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT.
 
Each 1240000.00
335 Supply, installation, testing and commissioning of Diesel
Engine Driven Main Fire Pump suitable for automatic
operation and consisting of followings complete in all
respects as required.
a.   1 No. horizontal split casing centrifugal type fire pump
capable of delivering 2850 LPM against a total head of 110 metres, so as to ensure a minimum pressure of 3.5 kg. per sq.cm at the farthest top most hydrant / outlet with pump casing of cast iron to grade FG 200, IS 210-1978 and parts like impeller, shaft sleeve, bearing ring, etc., of non-corrosive metal either like bronze, brass or gun metal and shaft of
stainless steel.
b.   100 BHP, 1500 RPM water cooled with radiator, diesel
engine conforming to relevant BS & IS standard complete.
c.   Auto starting mechanism, 12 volts / 24 volts electric
starting equipment like self motor, dynamo, solenoid
switches etc.
d.   110 litres capacity diesel tank mounted over stand
fabricated using 25mm x 25mm x 6mm size MS angle
providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre filter, after filter etc
e.   Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m outside pump house duly
insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessary MS support arrangements from wall or ceiling as per site condition.
f.  Dash board consisting of the instruments like Temperature Gauge, Galvano Type DC Ammeter, Lubricant Oil Pressure Gauge, Ignition Switch, Emergency Stop and all other
protection equipments as per specification, stop soleneid for auto stop in the event of fault with audio indications, painted with Post Office Red Colour etc., as required.
g.   12 V / 24 V, storage battery, maintenance free tape,
180AH rating. MS fabricated common base plate, coupling
guard, foundation bolts, etc., as required.
h.   Positioning the Diesel Engine Driven Fire Pump over
cement concrete foundation using suitable size anti vibration mounting arrangements.
All works including conveying, fixing and incidental charges, etc., completed as per standard specification and as directed by the Departmental Officers. Make: KIRLOSKAR / EQUIVALENT.
Each 1145000.00
336 Supply, erection, testing and commissioning of 180
LPM, 70 metres Head Pressurization Pump with 10HP electrical motor of Kirloskar make with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges, etc., complete as per standard specification and as
directed by the Departmental Officers. Make:
KIRLOSKAR / EQUIVALENT.
Each 102000.00
337 Supply, erection, testing and commissioning of Fire
Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition
wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: KIARTAR / OMEX /
EQUIVALENT.
Each 14500.00
338 Supply, erection, testing and commissioning of Air
Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.
Each 1450.00
339 Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.    
a 100mm dia Each 280.00
b 80mm dia Each 270.00
c 50mm dia Each 250.00
d 40mm dia Each 140.00
340 Supply and fixing of stored pressure ABC (Mono
Ammonium Phospate) Powder Type Fire Extinguisher of
6 kg. capacity as per IS:15683 with pressure gauge,
discharge hose & control nozzle, wall mounting
bracket, safety clip etc., including conveyance, all
incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition
wherever found neccessary etc, complete as per
standard specification and as directed by the
Departmental Officers. Make: EXCELLENT / SAFETY
FIRST / EQUIVALENT
Each 4500.00
341 Supply and fixing of Carbon-di-Oxide Gas Type 2 kg. capacity Fire Extinguisher as per New IS15683, complete with control valve, discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT Each 7500.00
342 Supply and kept in position of Trolley Mounted Water
CO2 Stored Pressure Type 50 litres capacity Fire
Extinguisher as per IS13385, complete with control
valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition
wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: EXCELLENT / SAFETY
FIRST / EQUIVALENT
Each 21000.00
343 Supply and kept in position of Trolley Mounted Type 22.5 kg. Carbon-di-Oxide Fire Extinguisher as per IS15683, complete with control valve, gun metal cap, pressure gauge, operation sticker, discharge hose, mounting trolley with moving wheel, safety clip, etc., including conveyance, all incidental charges,
neccessary scaffolding and re-doing the dismantled
portions to its original condition wherever found
neccessary, etc., complete as per standard
specification and as directed by the Departmental
Officers. Make: EXCELLENT / SAFETY FIRST /
EQUIVALENT
Each 29000.00
344 Servicing the SS Hydrant Valves by disconnecting from pipe line, dismantling, checking the operation of
rotating spindle, replacing rubber '0' ring of valve
seating, repalcing rubber gasket of 80mm dia OD x
65mm dia ID, repalcing the 5/8" x 21/2 bolt, nut,
washers, re-connecting with hydrant system as per standard methods and as directed by the Departmental Officers.
Each 1450.00
345 Servicing the First Aid Hose Reel Drum assembly by
disconnecting from hydrant line, replacing shut off
nozzle, warm clip, lubricating the rotating assembly, replacing 20mm dia, 30 metres long rubber hose, re­connecting with hydrant system as per standard methods and as directed by the Departmental Officers.
Each 3500.00
346 Servicing the following sizes of cast iron body Sluice
Valves by disconnecting from hydrant line, dismantling, inspecting the internal shutter, replacing valve seating, checking operating lever, lubricating for moving parts, re-connecting with hydrant system, as per standard methods and as directed by the Departmental Officers.
   
a 150mm dia Each 2700.00
b 100mm dia Each 1800.00
347 Supply and fixing in position of 12 Volt 180 AH Lead
Acid, Sealed Maintenance Free (SMF) batteries with
connecting leads, lugs terminal post, etc., as per
standard methods and including conveyance, all
incidental charges, neccessary scaffolding and re-doing
the dismantled portions to its original condition
wherever found neccessary, etc., complete as per
standard specification and as directed by the
Departmental Officers. Make: EXCELLENT / SAFETY
FIRST / EQUIVALENT.
Each 25000.00

 

SI. No. Description of Materials Unit Basic Rate approved for the year 2019-2020 (w.e.f. 17.06.2019) WORKING PRESSURE
4 kg. per cm2 6 kg. per cm2 10 kg. per cm2
  WATER SUPPLY AND SANITARY ARRANGEMENTS        
348 PVC ITEMS FINOLEX (OR) EQUIVALENT (WITH ISI MONOGRAM)        
1 PVC Pipes        
a 15mm dia RM -- -- 14.6
b 20mm dia RM -- -- 21.6
c 25mm dia RM -- 36.8
d 32mm dia RM -- -- 55.1
e 40mm dia RM -- -- 86.3
f 50mm dia RM 55.1 86.3 129
g 63mm dia RM 79.8 116.8 --
h 75mm dia RM 110.9 166.3 --
i 90mm dia RM 129.3 197.6 --
j 110mm dia RM 172.8 259.3
I 160mm dia RM 357 506 --
Note (1)  For Rainwater down fall pipe works, only PVC Pipe of working Pressure of 4 kg. per sq.cm. shall be adopted.
(2) For Sanitary arrangement items of
works, only PVC Pipe of working Pressure of 6 kg. per sq.cm. shall be adopted.
(3)  For Water Supply arrangement items of works, only PVC Pipe of working Pressure of 10 kg. per sq.cm. shall be adopted.
       
349 PVC Specials for water supply arrangements    
A Coupler